JEEP BUMPERS
Showing 65–96 of 177 results
-
Rear Bumpers
JK BFH II Rear Bumper Tabs Lights Poison Spyder – 17-17-021-DL
JK BFH II Rear Bumper Tabs Lights for Jeep Wrangler JK 2007-2016. Poison Spyder BFH II Rear Bumpers are designed for those hardcore four-wheelers who value strength, simplicity and function. This bumper was literally Built For the Hammers with the best ground clearance and departure angle possible. It is no wider than the Jeep JK Wrangler rear body tub, with angled facets to improve its ability to slide over the rocks while still protecting the corner of the tub from drop-offs and ledges.
This version of the BFH II features CNC machined high clearance recovery shackle tabs. For the ultimate in strength and durability, pair it with the JK BFH II Rear Crossmember.
Features:- Low profile faceted design for high clearance of trail obstacles
- CNC laser cut from 3/16 plate steel, precision brake-formed for a perfect fit
- High clearance recovery shackle tabs CNC machined from 1 thick plate steel
- Mounts for dual recessed 6 LED light bars
- Installation requires cutting/trimming of Jeep frame rails and rear crossmember
Plate Steel Construction
The BFH II Rear Bumper is CNC laser-cut from high strength 3/16 inch plate steel, then precision brake-formed for an exact fit. In keeping with its minimalist design parameter, the BFH II Rear Bumper has no provisions for a spare tire carrier. This bumper is intended for those hard-core wheelers who either wheel without a spare or strap the spare down into the bed of the Jeep. It may also be compatible with the OE tailgate-mounted spare tire carrier, depending on the size of the spare tire used.
High Clearance and Departure Angle
The faceted plate steel design of the JK BFH II Rear Bumper provides the Most ground/obstacle clearance and best departure angle of any JK rear bumper on the market. To achieve this, installation requires trimming the bulky rear frame rails and Stock bumper mounts. A laser-cut steel template is provided to assist with making the right cuts. These modifications include cutting into the Stock rear crossmember. At the installers discretion, the Stock rear crossmember may be plated across the open cut (materials to do this are Not included), or the crossmember removed completely.
Optional Replacement Crossmember
If the Stock crossmember is removed completely, it may be replaced with the JK BFH II Rear Crossmember (Note that there are versions of the BFH II Crossmember with or without a receiver hitch-this particular version of the BFH II Rear Bumper is specificaly designed to work with the non-receiver version-it will Not work with the crossmember that has the integrated hitch receiver (p/n 17-17-030).
High Clearance Shackle Tabs
The JK BFH II Rear Bumper includes heavy duty, high clearance Recovery Shackle Tabs. These tabs were CAD designed specifically for use with this bumper, with a high-clearance design to minimize loss of departure angle and to handle sliding off of rocks rather than hanging up on them. The tabs are CNC machined from 1 inch thick plate steel to provide a secure attachment point for 3/4 inch recovery shackles (sold separately).Notes: Installation requires cutting of Stock frame rails! Please read through the Installation Instructions so that you are Fully aware of the modifications required to your Jeep frame rails, before purchasing. This product ships as bare steel it will need to be painted or powdercoated prior to final installation. We do Not offer a powdercoat option for this item.
SKU: 17-17-021-DL-PSC -
Rear Bumpers
JK BFH II Rear Bumper Tabs Poison Spyder – 17-17-021-D
JK BFH II Rear Bumper Tabs for Jeep Wrangler JK 2007-2016. Poison Spyder BFH II Rear Bumpers are designed for those hardcore four-wheelers who value strength, simplicity and function. This bumper was literally Built For the Hammers with the best ground clearance and departure angle possible. It is no wider than the Jeep JK Wrangler rear body tub, with angled facets to improve its ability to slide over the rocks while still protecting the corner of the tub from drop-offs and ledges.
This version of the BFH II features CNC machined high clearance recovery shackle tabs. For the ultimate in strength and durability, pair it with the JK BFH II Rear Crossmember.
Features:
Low profile faceted design for high clearance of trail obstacles
CNC laser cut from 3/16 plate steel, precision brake-formed for a perfect fit
High clearance recovery shackle tabs CNC machined from 1 thick plate steel
Installation requires cutting/trimming of Jeep frame rails and rear crossmember
Plate Steel Construction
The BFH II Rear Bumper is CNC laser-cut from high strength 3/16 and plate steel, then precision brake-formed for an exact fit. In keeping with its minimalist design parameter, the BFH II Rear Bumper has no provisions for a spare tire carrier. This bumper is intended for those hard-core wheelers who either wheel without a spare or strap the spare down into the bed of the Jeep. It may also be compatible with the OE tailgate-mounted spare tire carrier, depending on the size of the spare tire used.
High Clearance & Departure Angle
The faceted plate steel design of the JK BFH II Rear Bumper provides the Most ground/obstacle clearance and best departure angle of any JK rear bumper on the market. To achieve this, installation requires trimming the bulky rear frame rails and Stock bumper mounts. A laser-cut steel template is provided to assist with making the right cuts. These modifications include cutting into the Stock rear crossmember. At the installer discretion, the Stock rear crossmember may be plated across the open cut (materials to do this are Not included), or the crossmember removed completely.
Optional Replacement Crossmember
If the Stock crossmember is removed completely, it may be replaced with the JK BFH II Rear Crossmember (Note that there are versions of the BFH II Crossmember with or without a receiver hitch-this particular version of the BFH II Rear Bumper is specificaly designed to work with the non-receiver version-it will Not work with the crossmember that has the integrated hitch receiver (p/n 17-17-030).
High Clearance Shackle Tabs
The JK BFH II Rear Bumper includes heavy duty, high clearance Recovery Shackle Tabs. These tabs were CAD designed specifically for use with this bumper, with a high-clearance design to minimize loss of departure angle and to handle sliding off of rocks rather than hanging up on them. The tabs are CNC machined from 1 inch thick plate steel to provide a secure attachment point for 3/4 inch recovery shackles (sold separately).Notes: Installation requires cutting of Stock frame rails! Please read through the Installation Instructions so that you are Fully aware of the modifications required to your Jeep frame rails, before purchasing. This product ships as bare steel it will need to be painted or powdercoated prior to final installation. We do Not offer a powdercoat option for this item.
SKU: 17-17-021-D-PSC -
Rear Bumpers
JK BFH II Rear Crossmember Poison Spyder – 17-17-010
JK BFH II Rear Crossmember for Jeep Wrangler JK 2007-2016. By itself or used in conjunction with the JK BFH II Rear Bumper, this Built For the Hammers crossmember strengthens the Jeep JK Wrangler rear frame when trimmed for maximum ground clearance and departure angle.
Features:- Heavy Duty replacement for Stock crossmember
- Works with BFH II Rear Bumpers
- May by used by itself for minimalist bumper
- CNC laser cut brake-formed 3/16 steel plate
Plate Steel Construction
The BFH II Rear Crossmember is CNC laser-cut from high strength 3/16 inch plate steel, then precision brake-formed for an exact fit. Dimpled lighting holes remove unnecessary weight while creating a custom look for those who choose to run the crossmember by itself without a rear bumper to cover it.
High Clearance and Departure Angle
The minimalist design of the JK BFH II Rear Bumper provides the Most ground/obstacle clearance and best departure angle possible while preserving the integrity of the Jeep JK frame strength. Installation requires trimming the bulky rear frame rails and Stock bumper mounts and welding in the new crossmember. A laser-cut steel template is provided to assist with making the right cuts.
Use By Itself or With BFH II Rear BumperThe BFH II Rear Crossmember may be used by itself as an ultra-minimalist, high clearance rear bumper. But it is designed to be used with the Poison Spyder BFH II Rear Bumper. The bumper fits over the crossmember like a glove. Together, this combination provides the frame-strengthening characteristics of the crossmember along with the aesthetics of the BFH II Rear Bumper. This specific part number for the crossmember does Not include an integrated hitch receiver, so it can only be used with the K BFH II Rear Bumper – Tabs or K BFH II Rear Bumper – Tabs – Lights. A different version of the BFH II Crossmember is available with a hitch receiver (p/n 17-17-030)
NotES: Installation requires cutting of Stock frame rails and welding! Please read through the Installation Instructions so that you are Fully aware of the modifications required to your Jeep frame rails, before purchasing.
This product ships as bare steel it will need to be painted after installation.
SKU: 17-17-010-PSC -
Rear Bumpers
JK BFH II Rear Crossmember Receiver Poison Spyder – 17-17-030
JK BFH II Rear Crossmember Receiver for Jeep Wrangler JK 2007-2016. By itself or used in conjunction with the JK BFH II Rear Bumper, this Built For the Hammers crossmember strengthens the Jeep JK Wrangler rear frame when trimmed for maximum ground clearance and departure angle. Includes a built-in hitch receiver (Not rated for towing).
Features:- Heavy Duty replacement for Stock crossmember
- Works with BFH II Rear Bumpers
- May by used by itself for minimalist bumper
- CNC laser cut brake-formed 3/16 steel plate
Plate Steel Construction
The BFH II Rear Crossmember is CNC laser-cut from high strength 3/16 inch plate steel, then precision brake-formed for an exact fit. Dimpled lighting holes remove unnecessary weight while creating a custom look for those who choose to run the crossmember by itself without a rear bumper to cover it.
High Clearance and Departure Angle
The minimalist design of the JK BFH II Rear Bumper provides the Most ground/obstacle clearance and best departure angle possible while preserving the integrity of the Jeep JK frame strength. Installation requires trimming the bulky rear frame rails and Stock bumper mounts and welding in the new crossmember. A laser-cut steel template is provided to assist with making the right cuts.
Use By Itself or With BFH II Rear Bumper
The BFH II Rear Crossmember may be used by itself as an ultra-minimalist, high clearance rear bumper. But it is designed to be used with the Poison Spyder BFH II Rear Bumper.The bumper fits over the crossmember like a glove. Together, this combination provides the frame-strengthening characteristics of the crossmember along with the aesthetics of the BFH II Rear Bumper. This specific part number for the crossmember includes the integrated hitch receiver, so it can only be used with the K BFH II Rear Bumper – Receiver – Tabs or K BFH II Rear Bumper – Receiver – Tabs – Lights. A different version of the BFH II Crossmember is available without the hitch receiver (p/n 17-17-010)
Integrated Hitch Receiver
This version of the JK BFH II Rear Crossmember is designed with an integrated hitch receiver as a convenient recovery attachment or tow point. The hitch receiver is constructed of Standard 2 inch square hitch receiver material and will accept Most hitch bars. Safety chain loops are provided behind the crossmember, tucked up out of the way of rocks.Important: in order to preserve the lowest profile and maximum departure angle, the receiver tube is slightly shorter than Standard tow hitches. This may necessitate trimming of the end of some receiver bars. This also places the hitch pin into a non-Standard location for tow-rating. Because of this the hitch is Not technically rated for towing, even though its design is stronger than the factory tow hitch.
Notes: Installation requires cutting of Stock frame rails and welding! Please read through the Installation Instructions so that you are Fully aware of the modifications required to your Jeep frame rails, before purchasing.
This product ships as bare steel it will need to be painted after installation.
SKU: 17-17-030-PSC -
Tire Carriers
JK Body Mounted Tire Carrier Poison Spyder – 17-13-010
JK Body Mounted Tire Carrier for Jeep Wrangler JK 2007-2016. Poison Spyders JK Body Mounted Tire Carrier works with the Stock rear bumper or just about any aftermarket rear bumper, and can accommodate up to a 40 inch spare tire and accessories. The main tire carrier assembly is made of 1.5 inch DOM tubing for strength and great looks.
All of the plate steel components are CNC laser cut and brake-formed from 1/8 inch or 3/16 inch steel plate. The hinge and latch assemblies are designed to address common issues inherent in similar tire carriers from other manufacturers. The tire carrier comes with mounting points to add several Rot-Pax fluid packs as well as a Hi-Lift jack.
Features:- Mounts to body-independent of bumper
- May be used with Stock bumper or almost any aftermarket bumper
- Fits up to 40 inch tire
- Includes mounts for Roto-Pax cans, Hi-Lift Jack
- Highly engineered attachment and adjustment
SKU: 17-13-010-PSC -
Front Bumpers
JK Brawler FULL Width Front Bumper Brawler Bar Tabs Poison Spyder – 17-64-020-DBT
JK Brawler Full Width Front Bumper Brawler Bar Tabs for Jeep Wrangler JK 2007-2016. The Brawler Full Width Front Bumper for JK provides the highest ground and tire clearance possible in a Full width JK bumper. This bumper brings Poison Spyder form and function to the overlander market, and to those who would like to keep their Stock JK fender flares.
The bumper extends to the Full width of the Stock flares, to integrate with them cleanly while protecting them from trail hazards. This configuration includes recessed fog light buckets and high clearance recovery shackle tabs. Like all bumpers in the Brawler product line, the Full Width is fabricated from 3/16 inch plate steel, CNC laser-cut and precision brake-formed into a low profile, high clearance design. This product ships as bare steel. It will need to be painted or powdercoated prior to final installation. We do Not yet offer a powdercoat option for this item.
Features:- Full-width, multi-faceted design protects lower grille and extends to outer edge of Stock flares
- CNC laser cut from 3/16 plate steel, precision brake-formed for a perfect fit
- Recessed light buckets accept OE fog lamps or Rigid Industries Duallys by use of adapter plate (sold separately)
- Brawler Bar made of 1.5 X .120 wall DOM tubing with 1.25 OD X .120 wall DOM tube gussets
- High clearance recovery shackle tabs
- CNC machined from 1 thick plate steel
Full Width
Finally there is a Full Width front bumper that incorporates Poison Spyder attention to form and function, in an elegant package that integrates perfectly with the Stock Jeep or aftermarket Stock replacement fender flares. While this bumper was designed for those Jeep enthusiasts who prefer a more overland style and function to their Jeep build, or want to keep their factory flares, we could not simply make a Full-width monstrosity like so many unsightly bumpers already on the market. Even though it is Full width, and less likely to be used on the hard core rock trails, we still felt compelled to design it with maximum approach angle, ground clearance and tire clearance possible while still extending out to the Full width of the Stock flares to protect the corners of the Jeep.The lower skid plate is sold separately, so that those who would rather run without it (and gain even more ground clearance) may do so. The outriggers that extend to the edge of the flare are kept as tight to the original Brawler high clearance lines as possible, tapering outward toward the ends. This allows the tires the best access to grab obstacles to pull the Jeep up and over rather than impeding progress when metal meets rock. The outriggers are designed to integrate visually with the Stock fender flares, in a clean, almost factory look. The back side of the outrigger is scalloped to provide maximum clearance for up to a 37 inch tire with minimal suspension lift.
Plate Steel Construction
Every Brawler bumper starts out as a sheet of 3/16 inch plate steel. Our CNC laser cutter precisely cuts the flat pattern as designed in our 3D CAD system. Next the bumper parts are CNC brake-formed into the high clearance, multi-faceted pieces that will become a finished bumper. Highly skilled tradesmen weld each bumper together using precision-engineered assembly fixtures for a perfect fit. Finally the complete bumper is sent through our finishing department for final appearance surfacing and quality control checks.Brawler Bar
The Brawler Bar is modeled after the bar found on our original RockBrawler front bumper. It is a low-profile stinger designed to provide protection to the winch, grille and radiator area. The Brawler Bar is made of CNC laser-Notched, NC-bent 1.75 inch diameter .120 inch wall DOM tubing. The complex laser-cut Notch allows the Brawler Bar to be welded to two different planes on the surface of the bumper, providing incredible strength.The Brawler Bar is further strengthened by a pair of 1.25 inch DOM tubular gussets. Note: Warn PowerPlant winches are Not a direct fit with the DOM Tube gussets (they may be installed with some minor modifications by the installer).
Easy Installation
Poison Spyder Brawler series front bumpers can be mounted without cutting or altering the Jeep frame rails. The faceted design of the Brawler Full Width Front Bumper provides the best ground clearance and approach angle possible in a Full width bumper that does not require frame modifications. The factory Crash Bar may be left intact or removed for a sleek appearance and high clearance. If keeping the crash bar, we recommend adding the Brawler Lite Skid Plate (p/n 17-59-030, sold separately), which conceals the crash bar and protects the electronic sway bar disconnect.
Recessed Fog Lamp Mounts
Every Brawler Front Bumper comes with provisions for re-mounting your factory fog lamps. These consist of recessed fog lamp buckets that are made of CNC laser cut DUM tubing with a mounting flange designed to accept the mounting hardware of the Stock lamps. The recess and all-steel buckets help protect the lamps from the rocks. For those who do Not have the Stock fog lamps, or would like to upgrade to more powerful LED lamps, Poison Spyder offers a unique LED Fog Lamp Mounting Kit (p/n RIG-DLYFOGMNT) for installing a pair of Rigid Industries Dually LED lamps in the fog lamp locations.
Important: The Stock fog lamps used on the Jeep Wrangler 10th Anniversary Rubicon do Not fit into the fog lamp buckets on this bumper. If installing this bumper on a 10th Anniversary Rubicon, we suggest using a pair of Rigid Industries Dually or Dually D2 LED lamps along with our JK Dually Fog Lamp Mounts instead of the Stock fog lamps.
Winch Compatibility
The Brawler Full Width Front Bumper is designed to accept Most Warn winches, and winches from other manufacturers that conform to Warn Standardized winch mounting dimensions. The winch sits in a slight depression on the top surface of the bumper, with plenty of CNC laser cut plate steel gusseting inside the bumper shell, directly underneath the winch to provide maximum strength. The Winch Fairlead Mount (p/n 45-57-010) is sold separately, so that those who wish to Not run a winch are left with a clean looking, unobstructed top surface on their bumper. Important: installing the Warn Zeon winch on the Brawler Mid Front Bumper requires a set of our Zeon Winch Spacer Plates (p/n 45-57-010-03).
Recovery Shackle Tabs
Recovery Shackle Tabs are Standard equipment on the Brawler Full Width Front Bumper. These 3D CAD designed tabs are modeled after the high clearance tabs designed for our hard core BFH series bumpers, providing maximum approach angle while minimizing hang-ups on rock obstacles. They are CNC machined from 1 inch thick steel billet, specifically designed to accept our heavy duty 3/4 inch Recovery Shackles.
Optional Brawler Lite Skid
The optional Brawler Lite Skid Plate (p/n 17-59-030) attaches to the bottom of the Brawler Full Width Front Bumper to conceal and protect the Stock crash bar, plus it has an extension to protect the electronic swaybar disconnect motor found on Rubicon JKs.The skid is made of CNC laser-cut 3/16 inch plate steel, precision brake-formed for a precise fit to the Brawler Full Width Front Bumper (yes, the Brawler Lite and Brawler Full Width share the same skid plate).
A separate version of the Brawler Full Width Front Bumper is available with the DOM tubular Brawler Bar.The Brawler Full Width Front Bumper comes to you as bare steel, ready to accept paint or powdercoat in the color of your choice. A powdercoat option for this item is Not currently available directly through Poison Spyder. See your nearest Poison Spyder dealer for powdercoating options through a coating shop near you.
SKU: 17-64-020-DBT-PSC -
Front Bumpers
JK Brawler FULL Width Front Bumper Tabs Poison Spyder – 17-64-020-D
JK Brawler Full Width Front Bumper Tabs for Jeep Wrangler JK 2007-2016. The Brawler Full Width Front Bumper for JK provides the highest ground and tire clearance possible in a Full width JK bumper. This bumper brings Poison Spyder form and function to the overlander market, and to those who would like to keep their Stock JK fender flares.
The bumper extends to the Full width of the Stock flares, to integrate with them cleanly while protecting them from trail hazards. This configuration includes recessed fog light buckets and high clearance recovery shackle tabs. Like all bumpers in the Brawler product line, the Full Width is fabricated from 3/16 inch plate steel, CNC laser-cut and precision brake-formed into a low profile, high clearance design. This product ships as bare steel. It will need to be painted or powdercoated prior to final installation. We do Not yet offer a powdercoat option for this item.
Features:- Full-width, multi-faceted design protects lower grille and extends to outer edge of Stock flares
- CNC laser cut from 3/16 plate steel, precision brake-formed for a perfect fit
- Recessed light buckets accept OE fog lamps or Rigid Industries Duallys by use of adapter plate (sold separately)
- Brawler Bar made of 1.5 X .120 wall DOM tubing with 1.25 OD X .120 wall DOM tube gussets
- High clearance recovery shackle tabs
- CNC machined from 1 thick plate steel
Full Width
Finally there is a Full Width front bumper that incorporates Poison Spyders attention to form and function, in an elegant package that integrates perfectly with the Stock Jeep or aftermarket Stock replacement fender flares. While this bumper was designed for those Jeep enthusiasts who prefer a more overland style and function to their Jeep build, or want to keep their factory flares, we could not simply make a Full-width monstrosity like so many unsightly bumpers already on the market. Even though it is Full width, and less likely to be used on the hard core rock trails, we still felt compelled to design it with maximum approach angle, ground clearance and tire clearance possible while still extending out to the Full width of the Stock flares to protect the corners of the Jeep.The lower skid plate is sold separately, so that those who would rather run without it (and gain even more ground clearance) may do so. The outriggers that extend to the edge of the flare are kept as tight to the original Brawler high clearance lines as possible, tapering outward toward the ends. This allows the tires the best access to grab obstacles to pull the Jeep up and over rather than impeding progress when metal meets rock. The outriggers are designed to integrate visually with the Stock fender flares, in a clean, almost factory look. The back side of the outrigger is scalloped to provide maximum clearance for up to a 37 inch tire with minimal suspension lift.
Plate Steel Construction
Every Brawler bumper starts out as a sheet of 3/16 inch plate steel. Our CNC laser cutter precisely cuts the flat pattern as designed in our 3D CAD system. Next the bumper parts are CNC brake-formed into the high clearance, multi-faceted pieces that will become a finished bumper. Highly skilled tradesmen weld each bumper together using precision-engineered assembly fixtures for a perfect fit. Finally the complete bumper is sent through our finishing department for final appearance surfacing and quality control checks.
Easy Installation
Poison Spyder Brawler series front bumpers can be mounted without cutting or altering the Jeep frame rails. The faceted design of the Brawler Full Width Front Bumper provides the best ground clearance and approach angle possible in a Full width bumper that doesn’t require frame modifications. The factory Crash Bar may be left intact or removed for a sleek appearance and high clearance. If keeping the crash bar, we recommend adding the Brawler Lite Skid Plate (p/n 17-59-030, sold separately), which conceals the crash bar and protects the electronic sway bar disconnect.
Recessed Fog Lamp Mounts
Every Brawler Front Bumper comes with provisions for re-mounting your factory fog lamps. These consist of recessed fog lamp buckets that are made of CNC laser cut DUM tubing with a mounting flange designed to accept the mounting hardware of the Stock lamps. The recess and all-steel buckets help protect the lamps from the rocks. For those who do Not have the Stock fog lamps, or would like to upgrade to more powerful LED lamps, Poison Spyder offers a unique LED Fog Lamp Mounting Kit (p/n RIG-DLYFOGMNT) for installing a pair of Rigid Industries Dually LED lamps in the fog lamp locations.
Important: The Stock fog lamps used on the Jeep Wrangler 10th Anniversary Rubicon do Not fit into the fog lamp buckets on this bumper. If installing this bumper on a 10th Anniversary Rubicon, we suggest using a pair of Rigid Industries Dually or Dually D2 LED lamps along with our JK Dually Fog Lamp Mounts instead of the Stock fog lamps.
Winch Compatibility
The Brawler Full Width Front Bumper is designed to accept Most Warn winches, and winches from other manufacturers that conform to Warn Standardized winch mounting dimensions. The winch sits in a slight depression on the top surface of the bumper, with plenty of CNC laser cut plate steel gusseting inside the bumper shell, directly underneath the winch to provide maximum strength. The Winch Fairlead Mount (p/n 45-57-010) is sold separately, so that those who wish to Not run a winch are left with a clean looking, unobstructed top surface on their bumper. Important: installing the Warn Zeon winch on the Brawler Mid Front Bumper requires a set of our Zeon Winch Spacer Plates (p/n 45-57-010-03).
Recovery Shackle Tabs
Recovery Shackle Tabs are Standard equipment on the Brawler Full Width Front Bumper. These 3D CAD designed tabs are modeled after the high clearance tabs designed for our hard core BFH series bumpers, providing maximum approach angle while minimizing hang-ups on rock obstacles. They are CNC machined from 1 inch thick steel billet, specifically designed to accept our heavy duty 3/4 inch Recovery Shackles.
Optional Brawler Lite Skid
The optional Brawler Lite Skid Plate (p/n 17-59-030) attaches to the bottom of the Brawler Full Width Front Bumper to conceal and protect the Stock crash bar, plus it has an extension to protect the electronic swaybar disconnect motor found on Rubicon JKs.The skid is made of CNC laser-cut 3/16 inch plate steel, precision brake-formed for a precise fit to the Brawler Full Width Front Bumper (yes, the Brawler Lite and Brawler Full Width share the same skid plate).
A separate version of the Brawler Full Width Front Bumper is available with the DOM tubular Brawler Bar.The Brawler Full Width Front Bumper comes to you as bare steel, ready to accept paint or powdercoat in the color of your choice. A powdercoat option for this item is Not currently available directly through Poison Spyder. See your nearest Poison Spyder dealer for powdercoating options through a coating shop near you.
SKU: 17-64-020-D-PSC -
Rear Bumpers
JK Brawler FULL Width Rear Bumper Lights Tabs Poison Spyder – 17-62-040-DL
The Brawler Full Width Rear Bumper Lights Tabs for Jeep Wrangler JK 2007-2016 provides the highest ground and tire clearance possible in a Full width JK rear bumper. This bumper brings Poison Spyder form and function to the overlander market, and to those who would like to keep their Stock JK fender flares. The bumper extends to the Full width of the Stock flares, to integrate with them cleanly while protecting them from trail hazards.
This configuration includes high clearance recovery shackle tabs and a receiver hitch. Like all bumpers in the Brawler product line, the Full Width rear bumper is fabricated from 3/16 inch plate steel, CNC laser-cut and precision brake-formed into a low profile, high clearance design. This product ships as bare steel. It will need to be painted or powdercoated prior to final installation.
Features:- Full-width, multi-faceted design protects lower grille and extends to outer edge of Stock flares
- CNC laser cut from 3/16 plate steel, precision brake-formed for a perfect fit
- Recessed mounts for LED pod lights
- Integrated high clearance hitch receiver
Full Width
Finally there is a Full Width front bumper that incorporates Poison Spyder attention to form and function, in an elegant package that integrates perfectly with the Stock Jeep or aftermarket Stock replacement fender flares. While this bumper was designed for those Jeep enthusiasts who prefer a more overland style and function to their Jeep build, or want to keep their factory flares, we could Not simply make a Full-width monstrosity like so many unsightly bumpers already on the market.Even though it is Full width, and less likely to be used on the hard core rock trails, we still felt compelled to design it with maximum approach angle, ground clearance and tire clearance possible while still extending out to the Full width of the Stock flares to protect the corners of the Jeep.
The outriggers that extend to the edge of the flare are kept as tight to the original Brawler high clearance lines as possible, tapering outward toward the ends. This allows the best departure angles possible in a Full width rear bumper, minimizing the chances of hanging up as the rear tire comes off a rock or ledge. The outriggers are designed to integrate visually with the Stock fender flares, in a clean, almost factory look.
Bumper Plate Steel Construction
Every Brawler bumper starts out as a sheet of 3/16 inch plate steel. Our CNC laser cutter precisely cuts the flat pattern as designed in our 3D CAD system. Next the bumper parts are CNC brake-formed into the high clearance, multi-faceted pieces that will become a finished bumper. Highly skilled tradesmen weld each bumper together using precision-engineered assembly fixtures for a perfect fit. Finally the complete bumper is sent through our finishing department for final appearance surfacing and quality control checks.
Integrated Hitch Receiver
The integrated hitch receiver accepts Standard 2 inch hitches and recovery accessories. It is built in to the structure of the Brawler Full Width Rear Bumper in order to provide a higher clearance, tougher hitch that is there when you need it, but tucked up higher out of the way for better clearance and departure angles on the trail. Includes integrated safety chain loops.Important: The integrated hitch receiver is Not rated for towing. It is intended as a recovery attachment point only.
Rock Solid Mounting
The JK Brawler Full Width Rear Bumper incorporates an extra set of mounting bolts, along the bottom of the bumper which fasten into the rear crossmember. Combined with the mounting flange bolts at either side, the bumper is rigidly fastened by a total of 8 Grade 8 bolts, on three different planes to provide ultimate strength and rigidity to the mounted bumper. The drivers side floating flange allows for safe, secure tightening to the Jeep frame rails regardless of manufacturing variances from the Jeep factory.
Recovery Shackle Tabs
The Heavy Duty Recovery Shackle Tabs are CNC machined from 1 inch thick steel billet, specifically designed to accept our Heavy Duty 3/4 inch Recovery Shackles. These tabs are designed to match the high clearance aspects of the rest of the bumper and minimized hang-ups. These Heavy Duty Recovery Shackle Tabs come as Standard equipment on the Brawler Full Width Rear Bumper.SKU: 17-62-040-DL-PSC -
Rear Bumpers
JK Brawler FULL Width Rear Bumper Tabs Poison Spyder – 17-62-040-D
The Brawler Full Width Rear Bumper Tabs for Jeep Wrangler JK 2007-2016 provides the highest ground and tire clearance possible in a Full width JK rear bumper. This bumper brings Poison Spyder form and function to the overlander market, and to those who would like to keep their Stock JK fender flares. The bumper extends to the Full width of the Stock flares, to integrate with them cleanly while protecting them from trail hazards.
This configuration includes high clearance recovery shackle tabs and a receiver hitch. Like all bumpers in the Brawler product line, the Full Width rear bumper is fabricated from 3/16 inch plate steel, CNC laser-cut and precision brake-formed into a low profile, high clearance design. This product ships as bare steel. It will need to be painted or powdercoated prior to final installation.
Features:- Full-width, multi-faceted design protects lower grille and extends to outer edge of Stock flares
- CNC laser cut from 3/16 plate steel, precision brake-formed for a perfect fit
- High clearance recovery shackle tabs CNC machined from 1 steel
- Integrated high clearance hitch receiver
Full Width
Finally there is a Full Width front bumper that incorporates Poison Spyder attention to form and function, in an elegant package that integrates perfectly with the Stock Jeep or aftermarket Stock replacement fender flares. While this bumper was designed for those Jeep enthusiasts who prefer a more overland style and function to their Jeep build, or want to keep their factory flares, we couldn’t simply make a Full-width monstrosity like so many unsightly bumpers already on the market.Even though its Full width, and less likely to be used on the hard core rock trails, we still felt compelled to design it with maximum approach angle, ground clearance and tire clearance possible while still extending out to the Full width of the Stock flares to protect the corners of the Jeep.
The outriggers that extend to the edge of the flare are kept as tight to the original Brawler high clearance lines as possible, tapering outward toward the ends. This allows the best departure angles possible in a Full width rear bumper, minimizing the chances of hanging up as the rear tire comes off a rock or ledge. The outriggers are designed to integrate visually with the Stock fender flares, in a clean, almost factory look.
Bumper Plate Steel Construction
Every Brawler bumper starts out as a sheet of 3/16 inch plate steel. Our CNC laser cutter precisely cuts the flat pattern as designed in our 3D CAD system. Next the bumper parts are CNC brake-formed into the high clearance, multi-faceted pieces that will become a finished bumper. Highly skilled tradesmen weld each bumper together using precision-engineered assembly fixtures for a perfect fit. Finally the complete bumper is sent through our finishing department for final appearance surfacing and quality control checks.
Integrated Hitch Receiver
The integrated hitch receiver accepts Standard 2 inch hitches and recovery accessories. It is built in to the structure of the Brawler Full Width Rear Bumper in order to provide a higher clearance, tougher hitch that is there when you need it, but tucked up higher out of the way for better clearance and departure angles on the trail. Includes integrated safety chain loops.Important: The integrated hitch receiver is Not rated for towing. It is intended as a recovery attachment point only.
Rock Solid Mounting
The JK Brawler Full Width Rear Bumper incorporates an extra set of mounting bolts, along the bottom of the bumper which fasten into the rear crossmember. Combined with the mounting flange bolts at either side, the bumper is rigidly fastened by a total of 8 Grade 8 bolts, on three different planes to provide ultimate strength and rigidity to the mounted bumper. The drivers side floating flange allows for safe, secure tightening to the Jeep frame rails regardless of manufacturing variances from the Jeep factory.
Recovery Shackle Tabs
The Heavy Duty Recovery Shackle Tabs are CNC machined from 1 inch thick steel billet, specifically designed to accept our Heavy Duty 3/4 inch Recovery Shackles. These tabs are designed to match the high clearance aspects of the rest of the bumper and minimized hang-ups. These Heavy Duty Recovery Shackle Tabs come as Standard equipment on the Brawler Full Width Rear Bumper.SKU: 17-62-040-D-PSC -
Rear Bumpers
JK Brawler FULL Width Rear Bumper Tire Carrier Lights Tabs Poison Spyder – 17-62-050-DL
JK Brawler Full Width Rear Bumper Tire Carrier Lights Tabs for Jeep Wrangler JK 2007-2016 provides the highest ground and tire clearance possible in a Full width JK rear bumper. This bumper brings Poison Spyder form and function to the overlander market, and to those who would like to keep their Stock JK fender flares. The bumper extends to the Full width of the Stock flares, to integrate with them cleanly while protecting them from trail hazards.
This configuration includes high clearance recovery shackle tabs and a receiver hitch. Like all bumpers in the Brawler product line, the Full Width rear bumper is fabricated from 3/16 inch plate steel, CNC laser-cut and precision brake-formed into a low profile, high clearance design. This product ships as bare steel it will need to be painted or powdercoated prior to final installation.
Features:- Full-width, multi-faceted design protects lower grille and extends to outer edge of Stock flares
- CNC laser cut from 3/16 plate steel, precision brake-formed for a perfect fit
- Single action spare tire carrier opens with tailgate; heavy duty spindle/hinge, latch and 3-way adjustable tire mount
- High clearance recovery shackle tabs CNC machined from 1 steel
- Integrated high clearance hitch receiver
Full Width
Finally there is a Full Width front bumper that incorporates Poison Spyder attention to form and function, in an elegant package that integrates perfectly with the Stock Jeep or aftermarket Stock replacement fender flares. While this bumper was designed for those Jeep enthusiasts who prefer a more overland style and function to their Jeep build, or want to keep their factory flares, we could Not simply make a Full-width monstrosity like so many unsightly bumpers already on the market.Even though it is Full width, and less likely to be used on the hard core rock trails, we still felt compelled to design it with maximum approach angle, ground clearance and tire clearance possible while still extending out to the Full width of the Stock flares to protect the corners of the Jeep. The outriggers that extend to the edge of the flare are kept as tight to the original Brawler high clearance lines as possible, tapering outward toward the ends.
This allows the best departure angles possible in a Full width rear bumper, minimizing the chances of hanging up as the rear tire comes off a rock or ledge. The outriggers are designed to integrate visually with the Stock fender flares, in a clean, almost factory look.
Bumper Plate Steel Construction
Every Brawler bumper starts out as a sheet of 3/16 inch plate steel. Our CNC laser cutter precisely cuts the flat pattern as designed in our 3D CAD system. Next the bumper parts are CNC brake-formed into the high clearance, multi-faceted pieces that will become a finished bumper. Highly skilled tradesmen weld each bumper together using precision-engineered assembly fixtures for a perfect fit. Finally the complete bumper is sent through our finishing department for final appearance surfacing and quality control checks.
Single-Action Spare Tire Carrier
The Spare Tire Carrier Single-Action-Opening feature is a huge convenience for when you are trying to open the tailgate and tire carrier with one hand, when you have got an armload of gear or groceries in the other. Rather than latching to itself, the tire carrier is tethered to the tailgate so that they open and close in tandem. A custom designed tie-rod assembly, bumper mechanism and Tramp Stamp keep the two pieces perfectly aligned when open, but tight and rattle-free when closed.
Tire Carrier Plate Steel Construction
The RockBrawler II Spare Tire Carrier is fabricated entirely from CNC laser cut, precision brake-formed plate steel. The pieces are expertly welded together in a specially designed assembly fixture to ensure consistent fit and quality. A web gusset design is cut into the corner of the tire carrier to provide a little Poison Spyder flare.
Extreme Duty Hinge Assembly
The extreme duty hinge assembly includes a precision CNC machined spindle and housing, with a pair of high quality Timken tapered roller bearings to provide smooth operation under the heaviest loads A spindle seal at the bottom of the hinge assembly keeps your lubrication in, and dirt and water out. The hinge assembly is capped with a CNC machined billet aluminum cap with the Spyder emblem machined in.
2-Way Adjustable Tire Mount
The tire mount is adjustable up and down, as well as in and out, to accommodate a wide variety of tire sizes up to 39 inches. The adjust-ability allows the tire to be mounted as low as possible for any tire size, to keep a low center of gravity.
License Plate Relocation Mount
The included license plate mount places the license plate at the center of the spare tire, for those who choose to move it there. Unlike the original RockBrawler rear bumper, the RockBrawler II Rear Bumper with Tire Carrier does Not obstruct the placement of the Stock license plate frame, so the installer may choose to leave it in the Stock location or move it to the center of the rear tire using the included bracket.We recommend relocating it, as the Stock mount sticks out significantly from the side of the Jeep and is just begging to be torn off by a rock along the trail. If relocating the license plate, our License Plate Delete Cover (p/n 17-04-112) and LED License Plate and 3rd Brake Light (p/n 41-04-LP6) will be useful in completing the relocation.
Integrated Hitch Receiver
The integrated hitch receiver accepts Standard 2 inch hitches and recovery accessories. It is built in to the structure of the Brawler Full Width Rear Bumper in order to provide a higher clearance, tougher hitch that’s there when you need it, but tucked up higher out of the way for better clearance and departure angles on the trail. Includes integrated safety chain loops. Important: The integrated hitch receiver is Not rated for towing. It is intended as a recovery attachment point only.
Rock Solid Mounting
The JK Brawler Full Width Rear Bumper incorporates an extra set of mounting bolts, along the bottom of the bumper which fasten into the rear crossmember. Combined with the mounting flange bolts at either side, the bumper is rigidly fastened by a total of 8 Grade 8 bolts, on three different planes to provide ultimate strength and rigidity to the mounted bumper. The drivers side floating flange allows for safe, secure tightening to the Jeep frame rails regardless of manufacturing variances from the Jeep factory.
Recovery Shackle Tabs
The Heavy Duty Recovery Shackle Tabs are CNC machined from 1 inch thick steel billet, specifically designed to accept our Heavy Duty 3/4 inch Recovery Shackles. These tabs are designed to match the high clearance aspects of the rest of the bumper and minimized hang-ups. These Heavy Duty Recovery Shackle Tabs come as Standard equipment on the Brawler Full Width Rear Bumper.
Optional Hi-Lift Jack Mount
A custom Hi-Lift Jack Mount (p/n 45-61-011), available separately, is CNC laser cut and bolts to the top of the tire carrier. It features a distinctive web design to match the corner gusset detail on the RockBrawler II Tire Carrier, and mounts the Hi-Lift jack above and forward of the spare tire to keep it tucked up and away until needed.SKU: 17-62-050-DL-PSC -
Rear Bumpers
JK Brawler FULL Width Rear Bumper Tire Carrier Tabs Poison Spyder – 17-62-050-D
JK Brawler Full Width Rear Bumper Tire Carrier Tabs for Jeep Wrangler JK 2007-2016 provides the highest ground and tire clearance possible in a Full width JK rear bumper. This bumper brings Poison Spyder form and function to the overlander market, and to those who would like to keep their Stock JK fender flares. The bumper extends to the Full width of the Stock flares, to integrate with them cleanly while protecting them from trail hazards.
This configuration includes high clearance recovery shackle tabs and a receiver hitch. Like all bumpers in the Brawler product line, the Full Width rear bumper is fabricated from 3/16 inch plate steel, CNC laser-cut and precision brake-formed into a low profile, high clearance design. This product ships as bare steel it will need to be painted or powdercoated prior to final installation.
Features:- Full-width, multi-faceted design protects lower grille and extends to outer edge of Stock flares
- CNC laser cut from 3/16 plate steel, precision brake-formed for a perfect fit
- Single action spare tire carrier opens with tailgate; heavy duty spindle/hinge, latch and 3-way adjustable tire mount
- High clearance recovery shackle tabs CNC machined from 1 steel
- Integrated high clearance hitch receiver
Full Width
Finally there is a Full Width front bumper that incorporates Poison Spyder attention to form and function, in an elegant package that integrates perfectly with the Stock Jeep or aftermarket Stock replacement fender flares. While this bumper was designed for those Jeep enthusiasts who prefer a more overland style and function to their Jeep build, or want to keep their factory flares, we could Not simply make a Full-width monstrosity like so many unsightly bumpers already on the market.Even though it is Full width, and less likely to be used on the hard core rock trails, we still felt compelled to design it with maximum approach angle, ground clearance and tire clearance possible while still extending out to the Full width of the Stock flares to protect the corners of the Jeep. The outriggers that extend to the edge of the flare are kept as tight to the original Brawler high clearance lines as possible, tapering outward toward the ends.
This allows the best departure angles possible in a Full width rear bumper, minimizing the chances of hanging up as the rear tire comes off a rock or ledge. The outriggers are designed to integrate visually with the Stock fender flares, in a clean, almost factory look.
Bumper Plate Steel Construction
Every Brawler bumper starts out as a sheet of 3/16 inch plate steel. Our CNC laser cutter precisely cuts the flat pattern as designed in our 3D CAD system. Next the bumper parts are CNC brake-formed into the high clearance, multi-faceted pieces that will become a finished bumper. Highly skilled tradesmen weld each bumper together using precision-engineered assembly fixtures for a perfect fit. Finally the complete bumper is sent through our finishing department for final appearance surfacing and quality control checks.
Single-Action Spare Tire Carrier
The Spare Tire Carrier Single-Action-Opening feature is a huge convenience for when you are trying to open the tailgate and tire carrier with one hand, when you have got an armload of gear or groceries in the other. Rather than latching to itself, the tire carrier is tethered to the tailgate so that they open and close in tandem. A custom designed tie-rod assembly, bumper mechanism and Tramp Stamp keep the two pieces perfectly aligned when open, but tight and rattle-free when closed.
Tire Carrier Plate Steel Construction
The RockBrawler II Spare Tire Carrier is fabricated entirely from CNC laser cut, precision brake-formed plate steel. The pieces are expertly welded together in a specially designed assembly fixture to ensure consistent fit and quality. A web gusset design is cut into the corner of the tire carrier to provide a little Poison Spyder flare.
Extreme Duty Hinge Assembly
The extreme duty hinge assembly includes a precision CNC machined spindle and housing, with a pair of high quality Timken tapered roller bearings to provide smooth operation under the heaviest loads A spindle seal at the bottom of the hinge assembly keeps your lubrication in, and dirt and water out. The hinge assembly is capped with a CNC machined billet aluminum cap with the Spyder emblem machined in.
2-Way Adjustable Tire Mount
The tire mount is adjustable up and down, as well as in and out, to accommodate a wide variety of tire sizes up to 39 inches. The adjust-ability allows the tire to be mounted as low as possible for any tire size, to keep a low center of gravity.
License Plate Relocation Mount
The included license plate mount places the license plate at the center of the spare tire, for those who choose to move it there. Unlike the original RockBrawler rear bumper, the RockBrawler II Rear Bumper with Tire Carrier does Not obstruct the placement of the Stock license plate frame, so the installer may choose to leave it in the Stock location or move it to the center of the rear tire using the included bracket.We recommend relocating it, as the Stock mount sticks out significantly from the side of the Jeep and is just begging to be torn off by a rock along the trail. If relocating the license plate, our License Plate Delete Cover (p/n 17-04-112) and LED License Plate and 3rd Brake Light (p/n 41-04-LP6) will be useful in completing the relocation.
Integrated Hitch Receiver
The integrated hitch receiver accepts Standard 2 inch hitches and recovery accessories. It is built in to the structure of the Brawler Full Width Rear Bumper in order to provide a higher clearance, tougher hitch that is there when you need it, but tucked up higher out of the way for better clearance and departure angles on the trail. Includes integrated safety chain loops. Important: The integrated hitch receiver is Not rated for towing. It is intended as a recovery attachment point only.
Rock Solid Mounting
The JK Brawler Full Width Rear Bumper incorporates an extra set of mounting bolts, along the bottom of the bumper which fasten into the rear crossmember. Combined with the mounting flange bolts at either side, the bumper is rigidly fastened by a total of 8 Grade 8 bolts, on three different planes to provide ultimate strength and rigidity to the mounted bumper. The drivers side floating flange allows for safe, secure tightening to the Jeep frame rails regardless of manufacturing variances from the Jeep factory.
Recovery Shackle Tabs
The Heavy Duty Recovery Shackle Tabs are CNC machined from 1 inch thick steel billet, specifically designed to accept our Heavy Duty 3/4 inch Recovery Shackles. These tabs are designed to match the high clearance aspects of the rest of the bumper and minimized hang-ups. These Heavy Duty Recovery Shackle Tabs come as Standard equipment on the Brawler Full Width Rear Bumper.
Optional Hi-Lift Jack Mount
A custom Hi-Lift Jack Mount (p/n 45-61-011), available separately, is CNC laser cut and bolts to the top of the tire carrier. It features a distinctive web design to match the corner gusset detail on the RockBrawler II Tire Carrier, and mounts the Hi-Lift jack above and forward of the spare tire to keep it tucked up and away until needed.SKU: 17-62-050-D-PSC -
Front Bumpers
JK Brawler Lite Front Bumper Brawler Bar Plate Gussets Poison Spyder – 17-59-010-B
JK Brawler Lite Front Bumper Brawler Bar Plate Gussets for Jeep Wrangler JK 2007-2016. The Brawler Lite front bumper for JK is a grille-width, high clearance bumper designed to combine hard core off-road performance with Full features. This bumper is fabricated from 3/16 inch plate steel, CNC laser-cut and precision brake-formed into a low profile, high clearance design.
The ends of the bumper extend far enough to protect the lower corner of the JK grille, but Not far enough to hinder tire clearance or tire access to vertical obstacles. This product ships as bare steel. It will need to be painted or powdercoated prior to final installation. We do Not offer a powdercoat option for this item.
Features:- Compact, multi-faceted design protects lower grille corners while giving tires plenty of clearance and access to climb obstacles
- CNC laser cut from 3/16 plate steel, precision brake-formed for a perfect fit
- Recessed light buckets accept OE fog lamps or Rigid Industries Duallys by use of adapter plate (sold separately)
- Brawler Bar made of 1.5 X .120 wall DOM tubing with 3/16 plate steel gussets
- Plate Steel Construction
This bumper is fabricated from 3/16 inch plate steel, CNC laser-cut and precision brake-formed into a low profile, high clearance design. The ends of the bumper extend far enough to protect the lower corner of the JK grille, but Not far enough to hinder tire clearance or tire access to vertical obstacles.
Brawler Bar
The Brawler Bar is modeled after the bar found on our original RockBrawler front bumper. It is a low-profile stinger designed to provide protection to the winch, grille and radiator area. The Brawler Bar is made of CNC laser-Notched, NC-bent 1.75 inches diameter .120 inch wall DOM tubing. The complex laser-cut Notch allows the Brawler Bar to be welded to two different planes on the surface of the bumper, providing incredible strength.Two gusset styles are offered for strengthening the Brawler Bar. CNC laser-cut brake-formed 3/16 inch plate steel or CNC laser Notched DOM tubing. Note: Warn PowerPlant winches are Not a direct-fit with the DOM Tube gussets (they may be installed with some minor modifications by the installer).
Easy Installation
Unlike the Poison Spyder BFH series bumpers for JK, the Brawler Lite can be mounted without cutting or altering the Jeep frame rails. The faceted design of the Brawler Lite provides the best ground clearance and approach angle possible in a bumper that does Not require frame modifications. The factory Crash Bar may be left intact or removed for a sleek appearance and high clearance. If keeping the crash bar, we recommend adding the Brawler Lite Skid Plate (sold separately), which conceals the crash bar and protects the electronic sway bar disconnect.
Recessed Fog Lamp Mounts
Brawler Lite comes with built-in, recessed fog lamp mounts that are designed to easily accept your Stock fog lamps. And these are Not just simple light tabs placed behind a hole in the bumperthey are recessed in a bucket made of a Full tubular section to encircle the lamp and keep light from annoyingly leaking behind and around the bumper. Adding further convenience are mounting holes for re-installing the harness retainer clips for the factory wiring, to keep the wiring neatly secured. If you would like a lot more power than the factory fog lamps provide, you can opt to install a set of Rigid Industries Dually or D2 Dually LED lamps using our JK Fog Light Mounts for Rigid Industries Dually/D2.
Important: The Stock fog lamps used on the Jeep Wrangler 10th Anniversary Rubicon do Not fit into the fog lamp buckets on this bumper. If installing this bumper on a 10th Anniversary Rubicon, we suggest using a pair of Rigid Industries Dually or Dually D2 LED lamps along with our JK Dually Fog Lamp Mounts instead of the Stock fog lamps.
Winch Compatibility
The Brawler Lite top-mounted, integrated winch mount is part of the Fully boxed, internally gusseted bumper shell. Winches that are mounted inside the bumper lose this box strength as well as the strength of internal gussets. The Brawler Lite is designed to accept Most Warn and other brand winches that use the popular 10 inch X 4.5 inch mounting pattern, with a few small exceptions. Warn Powerplant winches fit the Brawler Lite with Brawler Bar and Plate Gussets just fine, however it will require slight modifications to use this winch with the Tube Gusset variant. Mounting the Warn Zeon winches requires our Zeon Winch Spacer Plates. See the FAQ section below for further information on both of these winches.
Recovery Shackle Tabs
Optional Recovery Shackle Tabs are modeled after the high clearance tabs designed for our hard core BFH series bumpers. These tabs are angle to provide maximum approach angle. They are CNC machined from 1 inch thick steel billet, specifically designed to accept our heavy duty 3/4 inch Recovery Shackles. Selecting this option will get you a pair of these tabs, expertly welded to the Brawler Lite bumper.
Separate versions of the Brawler Lite are available without the Brawler Bar or with the Trail Stinger. The Brawler Lite comes to you as bare steel, ready to accept paint or powdercoat in the color of your choice. A powdercoat option for this item is Not currently available directly through Poison Spyder.SKU: 17-59-010-B-PSC -
Front Bumpers
JK Brawler Lite Front Bumper Brawler Bar Plate Gussets Tabs Black Poison Spyder – 17-59-010-DBP1
Front BumpersJK Brawler Lite Front Bumper Brawler Bar Plate Gussets Tabs Black Poison Spyder – 17-59-010-DBP1
JK Brawler Lite Front Bumper Brawler Bar Plate Gussets Tabs Black for Jeep Wrangler JK 2007-2016. The Brawler Lite front bumper for JK is a grille-width, high clearance bumper designed to combine hard core off-road performance with Full features.
This bumper is fabricated from 3/16 inch plate steel, CNC laser-cut and precision brake-formed into a low profile, high clearance design. The ends of the bumper extend far enough to protect the lower corner of the JK grille, but Not far enough to hinder tire clearance or tire access to vertical obstacles. This product ships as bare steel it will need to be painted or powdercoated prior to final installation. We do Not offer a powdercoat option for this item.
Features:- SpyderShell Armor Coat finish with 5-Year Warranty
- Compact, multi-faceted design protects lower grille corners while giving tires plenty of clearance and access to climb obstacles
- CNC laser cut from 3/16 plate steel, precision brake-formed for a perfect fit
- Recessed light buckets accept OE fog lamps or Rigid Industries Duallys by use of adapter plate (sold separately)
Plate Steel Construction
This bumper is fabricated from 3/16 inch plate steel, CNC laser-cut and precision brake-formed into a low profile, high clearance design. The ends of the bumper extend far enough to protect the lower corner of the JK grille, but Not far enough to hinder tire clearance or tire access to vertical obstacles.
Brawler Bar
The Brawler Bar is modeled after the bar found on our original RockBrawler front bumper. It is a low-profile stinger designed to provide protection to the winch, grille and radiator area. The Brawler Bar is made of CNC laser-Notched, NC-bent 1.75 inch diameter .120 inch wall DOM tubing. The complex laser-cut Notch allows the Brawler Bar to be welded to two different planes on the surface of the bumper, providing incredible strength. Two gusset styles are offered for strengthening the Brawler Bar. CNC laser-cut brake-formed 3/16 inch plate steel or CNC laser Notched DOM tubing. Note: Warn PowerPlant winches are Not a direct-fit with the DOM Tube gussets (they may be installed with some minor modifications by the installer).
Easy Installation
Unlike the Poison Spyder BFH series bumpers for JK, the Brawler Lite can be mounted without cutting or altering the Jeep frame rails. The faceted design of the Brawler Lite provides the best ground clearance and approach angle possible in a bumper that does Not require frame modifications. The factory Crash Bar may be left intact or removed for a sleek appearance and high clearance. If keeping the crash bar, we recommend adding the Brawler Lite Skid Plate (sold separately), which conceals the crash bar and protects the electronic sway bar disconnect.
Recessed Fog Lamp Mounts
Brawler Lite comes with built-in, recessed fog lamp mounts that are designed to easily accept your Stock fog lamps. And these are Not just simple light tabs placed behind a hole in the bumper they are recessed in a bucket made of a Full tubular section to encircle the lamp and keep light from annoyingly leaking behind and around the bumper.Adding further convenience are mounting holes for re-installing the harness retainer clips for the factory wiring, to keep the wiring neatly secured. If you would like a lot more power than the factory fog lamps provide, you can opt to install a set of Rigid Industries Dually or D2 Dually LED lamps using our JK Fog Light Mounts for Rigid Industries Dually/D2.
Important: The Stock fog lamps used on the Jeep Wrangler 10th Anniversary Rubicon do Not fit into the fog lamp buckets on this bumper. If installing this bumper on a 10th Anniversary Rubicon, we suggest using a pair of Rigid Industries Dually or Dually D2 LED lamps along with our JK Dually Fog Lamp Mounts instead of the Stock fog lamps.
Winch Compatibility
The Brawler Lite top-mounted, integrated winch mount is part of the Fully boxed, internally gusseted bumper shell. Winches that are mounted inside the bumper lose this box strength as well as the strength of internal gussets.The Brawler Lite is designed to accept Most Warn and other brand winches that use the popular 10 inch X 4.5 inch mounting pattern, with a few small exceptions. Warn Powerplant winches fit the Brawler Lite with Brawler Bar and Plate Gussets just fine, however it will require slight modifications to use this winch with the Tube Gusset variant. Mounting the Warn Zeon winches requires our Zeon Winch Spacer Plates. See the FAQ section below for further information on both of these winches.
Recovery Shackle Tabs
Optional Recovery Shackle Tabs are modeled after the high clearance tabs designed for our hard core BFH series bumpers. These tabs are angle to provide maximum approach angle. They are CNC machined from 1 inch thick steel billet, specifically designed to accept our heavy duty 3/4 inch Recovery Shackles. Selecting this option will get you a pair of these tabs, expertly welded to the Brawler Lite bumper.Separate versions of the Brawler Lite are available without the Brawler Bar or with the Trail Stinger. The Brawler Lite comes to you as bare steel, ready to accept paint or powdercoat in the color of your choice. A powdercoat option for this item is Not currently available directly through Poison Spyder.
SKU: 17-59-010-DBP1-PSC -
Front Bumpers
JK Brawler Lite Front Bumper Brawler Bar Plate Gussets Tabs Poison Spyder – 17-59-010-DB
Front BumpersJK Brawler Lite Front Bumper Brawler Bar Plate Gussets Tabs Poison Spyder – 17-59-010-DB
JK Brawler Lite Front Bumper Brawler Bar Plate Gussets Tabs for Jeep Wrangler JK 2007-2016. The Brawler Lite front bumper for JK is a grille-width, high clearance bumper designed to combine hard core off-road performance with Full features.
This bumper is fabricated from 3/16 inch plate steel, CNC laser-cut and precision brake-formed into a low profile, high clearance design. The ends of the bumper extend far enough to protect the lower corner of the JK grille, but Not far enough to hinder tire clearance or tire access to vertical obstacles. This product ships as bare steel it will need to be painted or powdercoated prior to final installation. We do Not offer a powdercoat option for this item.
Features:- Compact, multi-faceted design protects lower grille corners while giving tires plenty of clearance and access to climb obstacles
- CNC laser cut from 3/16 plate steel, precision brake-formed for a perfect fit
- Recessed light buckets accept OE fog lamps or Rigid Industries Duallys by use of adapter plate (sold separately)
- Brawler Bar made of 1.5 X .120 wall DOM tubing with 3/16 plate steel gussets
- High clearance recovery shackle tabs CNC machined from 1 thick plate steel
Plate Steel Construction
This bumper is fabricated from 3/16 inch plate steel, CNC laser-cut and precision brake-formed into a low profile, high clearance design. The ends of the bumper extend far enough to protect the lower corner of the JK grille, but Not far enough to hinder tire clearance or tire access to vertical obstacles.
Brawler Bar
The Brawler Bar is modeled after the bar found on our original RockBrawler front bumper. It is a low-profile stinger designed to provide protection to the winch, grille and radiator area. The Brawler Bar is made of CNC laser-Notched, NC-bent 1.75 inch diameter .120 inch wall DOM tubing. The complex laser-cut Notch allows the Brawler Bar to be welded to two different planes on the surface of the bumper, providing incredible strength. Two gusset styles are offered for strengthening the Brawler Bar. CNC laser-cut brake-formed 3/16 inch plate steel or CNC laser Notched DOM tubing. Note: Warn PowerPlant winches are Not a direct-fit with the DOM Tube gussets (they may be installed with some minor modifications by the installer).
Easy Installation
Unlike the Poison Spyder BFH series bumpers for JK, the Brawler Lite can be mounted without cutting or altering the Jeep frame rails. The faceted design of the Brawler Lite provides the best ground clearance and approach angle possible in a bumper that does Not require frame modifications. The factory Crash Bar may be left intact or removed for a sleek appearance and high clearance. If keeping the crash bar, we recommend adding the Brawler Lite Skid Plate (sold separately), which conceals the crash bar and protects the electronic sway bar disconnect.
Recessed Fog Lamp Mounts
Brawler Lite comes with built-in, recessed fog lamp mounts that are designed to easily accept your Stock fog lamps. And these are Not just simple light tabs placed behind a hole in the bumper they are recessed in a bucket made of a Full tubular section to encircle the lamp and keep light from annoyingly leaking behind and around the bumper.Adding further convenience are mounting holes for re-installing the harness retainer clips for the factory wiring, to keep the wiring neatly secured. If you’d like a lot more power than the factory fog lamps provide, you can opt to install a set of Rigid Industries Dually or D2 Dually LED lamps using our JK Fog Light Mounts for Rigid Industries Dually/D2.
Important: The Stock fog lamps used on the Jeep Wrangler 10th Anniversary Rubicon do Not fit into the fog lamp buckets on this bumper. If installing this bumper on a 10th Anniversary Rubicon, we suggest using a pair of Rigid Industries Dually or Dually D2 LED lamps along with our JK Dually Fog Lamp Mounts instead of the Stock fog lamps.
Winch Compatibility
The Brawler Lite top-mounted, integrated winch mount is part of the Fully boxed, internally gusseted bumper shell. Winches that are mounted inside the bumper lose this box strength as well as the strength of internal gussets.The Brawler Lite is designed to accept Most Warn and other brand winches that use the popular 10 inch X 4.5 inch mounting pattern, with a few small exceptions. Warn Powerplant winches fit the Brawler Lite with Brawler Bar and Plate Gussets just fine, however it will require slight modifications to use this winch with the Tube Gusset variant. Mounting the Warn Zeon winches requires our Zeon Winch Spacer Plates. See the FAQ section below for further information on both of these winches.
Recovery Shackle Tabs
Optional Recovery Shackle Tabs are modeled after the high clearance tabs designed for our hard core BFH series bumpers. These tabs are angle to provide maximum approach angle. They are CNC machined from 1 inch thick steel billet, specifically designed to accept our heavy duty 3/4 inch Recovery Shackles. Selecting this option will get you a pair of these tabs, expertly welded to the Brawler Lite bumper.Separate versions of the Brawler Lite are available without the Brawler Bar or with the Trail Stinger. The Brawler Lite comes to you as bare steel, ready to accept paint or powdercoat in the color of your choice. A powdercoat option for this item is Not currently available directly through Poison Spyder.
SKU: 17-59-010-DB-PSC -
Front Bumpers
JK Brawler Lite Front Bumper Brawler Bar Tube Gussets Poison Spyder – 17-59-010-BT
JK Brawler Lite Front Bumper Brawler Bar Tube Gussets for Jeep Wrangler JK 2007-2016. The Brawler Lite front bumper for JK is a grille-width, high clearance bumper designed to combine hard core off-road performance with Full features. This bumper is fabricated from 3/16 inch plate steel, CNC laser-cut and precision brake-formed into a low profile, high clearance design.
The ends of the bumper extend far enough to protect the lower corner of the JK grille, but Not far enough to hinder tire clearance or tire access to vertical obstacles. This product ships as bare steel. It will need to be painted or powdercoated prior to final installation. We do Not offer a powdercoat option for this item.
Features:- Compact, multi-faceted design protects lower grille corners while giving tires plenty of clearance and access to climb obstacles
- CNC laser cut from 3/16 plate steel, precision brake-formed for a perfect fit
- Recessed light buckets accept OE fog lamps or Rigid Industries Duallys by use of adapter plate (sold separately)
- Brawler Bar made of 1.5 X .120 wall DOM tubing with 1.25 OD X .120 wall DOM tube gussets
This bumper is fabricated from 3/16 inch plate steel, CNC laser-cut and precision brake-formed into a low profile, high clearance design. The ends of the bumper extend far enough to protect the lower corner of the JK grille, but Not far enough to hinder tire clearance or tire access to vertical obstacles.
Brawler Bar
The Brawler Bar is modeled after the bar found on our original RockBrawler front bumper. It is a low-profile stinger designed to provide protection to the winch, grille and radiator area. The Brawler Bar is made of CNC laser-Notched, NC-bent 1.75 inch diameter .120 inch wall DOM tubing. The complex laser-cut Notch allows the Brawler Bar to be welded to two different planes on the surface of the bumper, providing incredible strength.Two gusset styles are offered for strengthening the Brawler Bar. CNC laser-cut brake-formed 3/16 inch plate steel or CNC laser Notched DOM tubing. Note: Warn PowerPlant winches are Not a direct-fit with the DOM Tube gussets (they may be installed with some minor modifications by the installer).
Easy Installation
Unlike the Poison Spyder BFH series bumpers for JK, the Brawler Lite can be mounted without cutting or altering the Jeep frame rails. The faceted design of the Brawler Lite provides the best ground clearance and approach angle possible in a bumper that does Not require frame modifications. The factory Crash Bar may be left intact or removed for a sleek appearance and high clearance. If keeping the crash bar, we recommend adding the Brawler Lite Skid Plate (sold separately), which conceals the crash bar and protects the electronic sway bar disconnect.
Recessed Fog Lamp Mounts
Brawler Lite comes with built-in, recessed fog lamp mounts that are designed to easily accept your Stock fog lamps. And these are Not just simple light tabs placed behind a hole in the bumperthey are recessed in a bucket made of a Full tubular section to encircle the lamp and keep light from annoyingly leaking behind and around the bumper. Adding further convenience are mounting holes for re-installing the harness retainer clips for the factory wiring, to keep the wiring neatly secured. If you would like a lot more power than the factory fog lamps provide, you can opt to install a set of Rigid Industries Dually or D2 Dually LED lamps using our JK Fog Light Mounts for Rigid Industries Dually/D2.
Important: The Stock fog lamps used on the Jeep Wrangler 10th Anniversary Rubicon do Not fit into the fog lamp buckets on this bumper. If installing this bumper on a 10th Anniversary Rubicon, we suggest using a pair of Rigid Industries Dually or Dually D2 LED lamps along with our JK Dually Fog Lamp Mounts instead of the Stock fog lamps.
Winch Compatibility
The Brawler Lite top-mounted, integrated winch mount is part of the Fully boxed, internally gusseted bumper shell. Winches that are mounted inside the bumper lose this box strength as well as the strength of internal gussets. The Brawler Lite is designed to accept Most Warn and other brand winches that use the popular 10 inch X 4.5 inch mounting pattern, with a few small exceptions. Warn Powerplant winches fit the Brawler Lite with Brawler Bar and Plate Gussets just fine, however it will require slight modifications to use this winch with the Tube Gusset variant. Mounting the Warn Zeon winches requires our Zeon Winch Spacer Plates. See the FAQ section below for further information on both of these winches.
Recovery Shackle Tabs
Optional Recovery Shackle Tabs are modeled after the high clearance tabs designed for our hard core BFH series bumpers. These tabs are angle to provide maximum approach angle. They are CNC machined from 1 inch thick steel billet, specifically designed to accept our heavy duty 3/4 inch Recovery Shackles. Selecting this option will get you a pair of these tabs, expertly welded to the Brawler Lite bumper.
Separate versions of the Brawler Lite are available without the Brawler Bar or with the Trail Stinger. The Brawler Lite comes to you as bare steel, ready to accept paint or powdercoat in the color of your choice. A powdercoat option for this item is Not currently available directly through Poison Spyder.SKU: 17-59-010-BT-PSC -
Front Bumpers
JK Brawler Lite Front Bumper Brawler Bar Tube Gussets Tabs Poison Spyder – 17-59-010-DBT
Front BumpersJK Brawler Lite Front Bumper Brawler Bar Tube Gussets Tabs Poison Spyder – 17-59-010-DBT
JK Brawler Lite Front Bumper Brawler Bar Tube Gussets Tabs for Jeep Wrangler JK 2007-2016. The Brawler Lite front bumper for JK is a grille-width, high clearance bumper designed to combine hard core off-road performance with Full features.
This bumper is fabricated from 3/16 inch plate steel, CNC laser-cut and precision brake-formed into a low profile, high clearance design. The ends of the bumper extend far enough to protect the lower corner of the JK grille, but Not far enough to hinder tire clearance or tire access to vertical obstacles. This product ships as bare steel it will need to be painted or powdercoated prior to final installation. We do Not offer a powdercoat option for this item.
Features:- Compact, multi-faceted design protects lower grille corners while giving tires plenty of clearance and access to climb obstacles
- CNC laser cut from 3/16 plate steel, precision brake-formed for a perfect fit
- Recessed light buckets accept OE fog lamps or Rigid Industries Duallys by use of adapter plate (sold separately)
- Brawler Bar made of 1.5 X .120 wall DOM tubing with 1.25 OD X .120 wall DOM tube gussets
- High clearance recovery shackle tabs
- CNC machined from 1 thick plate steel
Plate Steel Construction
This bumper is fabricated from 3/16 inch plate steel, CNC laser-cut and precision brake-formed into a low profile, high clearance design. The ends of the bumper extend far enough to protect the lower corner of the JK grille, but Not far enough to hinder tire clearance or tire access to vertical obstacles.
Brawler Bar
The Brawler Bar is modeled after the bar found on our original RockBrawler front bumper. It is a low-profile stinger designed to provide protection to the winch, grille and radiator area. The Brawler Bar is made of CNC laser-Notched, NC-bent 1.75 inch diameter .120 inch wall DOM tubing. The complex laser-cut Notch allows the Brawler Bar to be welded to two different planes on the surface of the bumper, providing incredible strength. Two gusset styles are offered for strengthening the Brawler Bar. CNC laser-cut brake-formed 3/16 inch plate steel or CNC laser Notched DOM tubing. Note: Warn PowerPlant winches are Not a direct-fit with the DOM Tube gussets (they may be installed with some minor modifications by the installer).
Easy Installation
Unlike the Poison Spyder BFH series bumpers for JK, the Brawler Lite can be mounted without cutting or altering the Jeep frame rails. The faceted design of the Brawler Lite provides the best ground clearance and approach angle possible in a bumper that does Not require frame modifications. The factory Crash Bar may be left intact or removed for a sleek appearance and high clearance. If keeping the crash bar, we recommend adding the Brawler Lite Skid Plate (sold separately), which conceals the crash bar and protects the electronic sway bar disconnect.
Recessed Fog Lamp Mounts
Brawler Lite comes with built-in, recessed fog lamp mounts that are designed to easily accept your Stock fog lamps. And these are Not just simple light tabs placed behind a hole in the bumper they are recessed in a bucket made of a Full tubular section to encircle the lamp and keep light from annoyingly leaking behind and around the bumper.Adding further convenience are mounting holes for re-installing the harness retainer clips for the factory wiring, to keep the wiring neatly secured. If you would like a lot more power than the factory fog lamps provide, you can opt to install a set of Rigid Industries Dually or D2 Dually LED lamps using our JK Fog Light Mounts for Rigid Industries Dually/D2.
Important: The Stock fog lamps used on the Jeep Wrangler 10th Anniversary Rubicon do Not fit into the fog lamp buckets on this bumper. If installing this bumper on a 10th Anniversary Rubicon, we suggest using a pair of Rigid Industries Dually or Dually D2 LED lamps along with our JK Dually Fog Lamp Mounts instead of the Stock fog lamps.
Winch Compatibility
The Brawler Lite top-mounted, integrated winch mount is part of the Fully boxed, internally gusseted bumper shell. Winches that are mounted inside the bumper lose this box strength as well as the strength of internal gussets.The Brawler Lite is designed to accept Most Warn and other brand winches that use the popular 10 inch X 4.5 inch mounting pattern, with a few small exceptions. Warn Powerplant winches fit the Brawler Lite with Brawler Bar and Plate Gussets just fine, however it will require slight modifications to use this winch with the Tube Gusset variant. Mounting the Warn Zeon winches requires our Zeon Winch Spacer Plates. See the FAQ section below for further information on both of these winches.
Recovery Shackle Tabs
Optional Recovery Shackle Tabs are modeled after the high clearance tabs designed for our hard core BFH series bumpers. These tabs are angle to provide maximum approach angle. They are CNC machined from 1 inch thick steel billet, specifically designed to accept our heavy duty 3/4 inch Recovery Shackles. Selecting this option will get you a pair of these tabs, expertly welded to the Brawler Lite bumper.Separate versions of the Brawler Lite are available without the Brawler Bar or with the Trail Stinger. The Brawler Lite comes to you as bare steel, ready to accept paint or powdercoat in the color of your choice. A powdercoat option for this item is Not currently available directly through Poison Spyder.
SKU: 17-59-010-DBT-PSC -
Front Bumpers
JK Brawler Lite Front Bumper Poison Spyder – 17-59-010
JK Brawler Lite Front Bumper for Jeep Wrangler JK 2007-2016. The Brawler Lite front bumper for JK is a Mid-width, high clearance bumper designed to combine hard core off-road performance with Full features.
This bumper is fabricated from 3/16 inch plate steel, CNC laser-cut and precision brake-formed into a low profile, high clearance design. The ends of the bumper extend far enough to protect the lower corner of the JK grille, but Not far enough to hinder tire clearance or tire access to vertical obstacles. This product ships as bare steel it will need to be painted or powdercoated prior to final installation. We do Not offer a powdercoat option for this item.
Features:- Compact, multi-faceted design protects lower grille corners while giving tires plenty of clearance and access to climb obstacles
- CNC laser cut from 3/16 plate steel, precision brake-formed for a perfect fit
- Recessed light buckets accept OE fog lamps or Rigid Industries Duallys by use of adapter plate (sold separately)
- Compact, multi-faceted design protects lower grille corners while giving tires plenty of clearance and access to climb obstacles
- CNC laser cut from 3/16 plate steel, precision brake-formed for a perfect fit
Unlike the Poison Spyder BFH series bumpers for JK, the Brawler Lite can be mounted without cutting or altering the Jeep frame rails. The faceted design of the Brawler Lite provides the best ground clearance and approach angle possible in a bumper that does Not require frame modifications. The factory Crash Bar may be left intact or removed for a sleek appearance and high clearance. If keeping the crash bar, we recommend adding the Brawler Lite Skid Plate (sold separately), which conceals the crash bar and protects the electronic sway bar disconnect.
The Brawler Lite features recessed buckets to mount the factory fog lamps, Fully protecting them in deep tubular sockets with direct-fit mounting flanges. ANother thoughtful feature are the conveniently placed loom mounting holes, for reinstalling the Christmas tree loom hangers of the factory fog lamp harness.
Important: The Stock fog lamps used on the Jeep Wrangler 10th Anniversary Rubicon do Not fit into the fog lamp buckets on this bumper. If installing this bumper on a 10th Anniversary Rubicon, we suggest using a pair of Rigid Industries Dually or Dually D2 LED lamps along with our JK Dually Fog Lamp Mounts instead of the Stock fog lamps.Any winch with a Standard 10 X 4.5 inch mounting pattern will bolt right on to the Brawler Lite. Beefy internal gusseting directly below the winch mount provides the strength to sustain long, heavy pulls. The center of the bumper, where the winch sits, is slightly recessed with the winch mounting on top, without compromising the structural integrity of the bumper by cutting a huge hole in the bumper structure to place the winch down inside like other manufacturers bumpers. If mounting a winch, you’ll need a Winch Fairlead Mount, sold separately.
Optional Recovery Shackle Tabs are modeled after the high clearance tabs designed for our hard core BFH series bumpers. These tabs are angle to provide maximum approach angle. They are CNC machined from 1 inch thick steel billet, specifically designed to accept our heavy duty 3/4 inch Recovery Shackles. Selecting this option will get you a pair of these tabs, expertly welded to the Brawler Lite bumper.
A separate version of the Brawler Lite is available with a tubular Brawler Bar. The Brawler Lite comes to you as bare steel, ready to accept paint or powdercoat in the color of your choice. A powdercoat option for this item is Not currently available directly through Poison Spyder. See your nearest Poison Spyder dealer for powdercoating options through a coating shop near you.
SKU: 17-59-010-PSC -
Front Bumpers
JK Brawler Lite Front Bumper Tabs Poison Spyder – 17-59-010-D
JK Brawler Lite Front Bumper Tabs for Jeep Wrangler JK 2007-2016. The Brawler Lite front bumper for JK is a grille-width, high clearance bumper designed to combine hard core off-road performance with Full features.
This bumper is fabricated from 3/16 inch plate steel, CNC laser-cut and precision brake-formed into a low profile, high clearance design. The ends of the bumper extend far enough to protect the lower corner of the JK grille, but Not far enough to hinder tire clearance or tire access to vertical obstacles. This product ships as bare steel it will need to be painted or powdercoated prior to final installation. We do Not offer a powdercoat option for this item.
Features:- Compact, multi-faceted design protects lower grille corners while giving tires plenty of clearance and access to climb obstacles
- CNC laser cut from 3/16 plate steel, precision brake-formed for a perfect fit
- Recessed light buckets accept OE fog lamps or Rigid Industries Duallys by use of adapter plate (sold separately)
- High clearance recovery shackle tabs
- CNC machined from 1 thick plate steel
Plate Steel Construction
This bumper is fabricated from 3/16 inch plate steel, CNC laser-cut and precision brake-formed into a low profile, high clearance design. The ends of the bumper extend far enough to protect the lower corner of the JK grille, but Not far enough to hinder tire clearance or tire access to vertical obstacles.
Brawler Bar
The Brawler Bar is modeled after the bar found on our original RockBrawler front bumper. It is a low-profile stinger designed to provide protection to the winch, grille and radiator area. The Brawler Bar is made of CNC laser-Notched, NC-bent 1.75 inch diameter .120 inch wall DOM tubing. The complex laser-cut Notch allows the Brawler Bar to be welded to two different planes on the surface of the bumper, providing incredible strength. Two gusset styles are offered for strengthening the Brawler Bar. CNC laser-cut brake-formed 3/16 inch plate steel or CNC laser Notched DOM tubing. Note: Warn PowerPlant winches are Not a direct-fit with the DOM Tube gussets (they may be installed with some minor modifications by the installer).
Easy Installation
Unlike the Poison Spyder BFH series bumpers for JK, the Brawler Lite can be mounted without cutting or altering the Jeep frame rails. The faceted design of the Brawler Lite provides the best ground clearance and approach angle possible in a bumper that doesn’t require frame modifications. The factory Crash Bar may be left intact or removed for a sleek appearance and high clearance. If keeping the crash bar, we recommend adding the Brawler Lite Skid Plate (sold separately), which conceals the crash bar and protects the electronic sway bar disconnect.
Recessed Fog Lamp Mounts
Brawler Lite comes with built-in, recessed fog lamp mounts that are designed to easily accept your Stock fog lamps. And these are Not just simple light tabs placed behind a hole in the bumper they are recessed in a bucket made of a Full tubular section to encircle the lamp and keep light from annoyingly leaking behind and around the bumper.Adding further convenience are mounting holes for re-installing the harness retainer clips for the factory wiring, to keep the wiring neatly secured. If you would like a lot more power than the factory fog lamps provide, you can opt to install a set of Rigid Industries Dually or D2 Dually LED lamps using our JK Fog Light Mounts for Rigid Industries Dually/D2.
Important: The Stock fog lamps used on the Jeep Wrangler 10th Anniversary Rubicon do Not fit into the fog lamp buckets on this bumper. If installing this bumper on a 10th Anniversary Rubicon, we suggest using a pair of Rigid Industries Dually or Dually D2 LED lamps along with our JK Dually Fog Lamp Mounts instead of the Stock fog lamps.
Winch Compatibility
The Brawler Lite top-mounted, integrated winch mount is part of the Fully boxed, internally gusseted bumper shell. Winches that are mounted inside the bumper lose this box strength as well as the strength of internal gussets.The Brawler Lite is designed to accept Most Warn and other brand winches that use the popular 10 inch X 4.5 inch mounting pattern, with a few small exceptions. Warn Powerplant winches fit the Brawler Lite with Brawler Bar and Plate Gussets just fine, however it will require slight modifications to use this winch with the Tube Gusset variant. Mounting the Warn Zeon winches requires our Zeon Winch Spacer Plates. See the FAQ section below for further information on both of these winches.
Recovery Shackle Tabs
Optional Recovery Shackle Tabs are modeled after the high clearance tabs designed for our hard core BFH series bumpers. These tabs are angle to provide maximum approach angle. They are CNC machined from 1 inch thick steel billet, specifically designed to accept our heavy duty 3/4 inch Recovery Shackles. Selecting this option will get you a pair of these tabs, expertly welded to the Brawler Lite bumper.Separate versions of the Brawler Lite are available without the Brawler Bar or with the Trail Stinger. The Brawler Lite comes to you as bare steel, ready to accept paint or powdercoat in the color of your choice. A powdercoat option for this item is Not currently available directly through Poison Spyder.
SKU: 17-59-010-D-PSC -
Front Bumpers
JK Brawler Lite Front Bumper Trail Stinger Poison Spyder – 17-59-010-ST
JK Brawler Lite Front Bumper Trail Stinger for Jeep Wrangler JK 2007-2016. The Brawler Lite front bumper for JK is a grille-width, high clearance bumper designed to combine hard core off-road performance with Full features. This bumper is fabricated from 3/16 inch plate steel, CNC laser-cut and precision brake-formed into a low profile, high clearance design. The ends of the bumper extend far enough to protect the lower corner of the JK grille, but Not far enough to hinder tire clearance or tire access to vertical obstacles. This product ships as bare steel. It will need to be painted or powdercoated prior to final installation. We do Not offer a powdercoat option for this item.
Features:- Compact, multi-faceted design protects lower grille corners while giving tires plenty of clearance and access to climb obstacles
- CNC laser cut from 3/16 plate steel, precision brake-formed for a perfect fit
- Recessed light buckets accept OE fog lamps or Rigid Industries Duallys by use of adapter plate (sold separately)
- Trail Stinger made of 1.5 X .120 wall DOM tubing with 1.25 OD X .120 wall DOM tube gussets
Plate Steel Construction
This bumper is fabricated from 3/16 inch plate steel, CNC laser-cut and precision brake-formed into a low profile, high clearance design. The ends of the bumper extend far enough to protect the lower corner of the JK grille, but Not far enough to hinder tire clearance or tire access to vertical obstacles.
Trail Stinger
The Trail Stinger used on this version of the Brawler Lite is modeled after the famous Trail Stinger originally developed and popularized by Poison Spyder. This time-honored design has proven itself on hundreds of Jeeps over the past decade, providing simple, clean lines along with a measure of forward-flop protection. The Trail Stinger is made of CNC laser-Notched, NC-bent 1.75 inch diameter .120 inch wall DOM tubing.The complex laser-cut Notch allows the Brawler Bar to be welded to two different planes on the surface of the bumper, providing incredible strength. The Trail Stinger is fortified by a pair of 1.25 inch diameter .120 inch wall DOM tube gussets. Note: Warn PowerPlant winches are Not a direct-fit with the DOM Tube gussets (they may be installed with some minor modifications by the installer). Brawler Lite is also available with the Brawler Bar or with no bar/stinger.
Easy Installation
Unlike the Poison Spyder BFH series bumpers for JK, the Brawler Lite can be mounted without cutting or altering the Jeep frame rails. The faceted design of the Brawler Lite provides the best ground clearance and approach angle possible in a bumper that doesn’t require frame modifications. The factory Crash Bar may be left intact or removed for a sleek appearance and high clearance. If keeping the crash bar, we recommend adding the Brawler Lite Skid Plate (sold separately), which conceals the crash bar and protects the electronic sway bar disconnect.
Recessed Fog Lamp Mounts
Brawler Lite comes with built-in, recessed fog lamp mounts that are designed to easily accept your Stock fog lamps. And these are Not just simple light tabs placed behind a hole in the bumper they are recessed in a bucket made of a Full tubular section to encircle the lamp and keep light from annoyingly leaking behind and around the bumper. Adding further convenience are mounting holes for re-installing the harness retainer clips for the factory wiring, to keep the wiring neatly secured. If you’d like a lot more power than the factory fog lamps provide, you can opt to install a set of Rigid Industries Dually or D2 Dually LED lamps using our JK Fog Light Mounts for Rigid Industries Dually/D2.
Important: The Stock fog lamps used on the Jeep Wrangler 10th Anniversary Rubicon do Not fit into the fog lamp buckets on this bumper. If installing this bumper on a 10th Anniversary Rubicon, we suggest using a pair of Rigid Industries Dually or Dually D2 LED lamps along with our JK Dually Fog Lamp Mounts instead of the Stock fog lamps.
Winch Compatibility
The Brawler Lite top-mounted, integrated winch mount is part of the Fully boxed, internally gusseted bumper shell. Winches that are mounted inside the bumper lose this box strength as well as the strength of internal gussets. The Brawler Lite is designed to accept Most Warn and other brand winches that use the popular 10 inch X 4.5 inch mounting pattern, with a few small exceptions. Warn Powerplant winches fit the Brawler Lite with Brawler Bar and Plate Gussets just fine, however it will require slight modifications to use this winch with the Tube Gusset variant. Mounting the Warn Zeon winches requires our Zeon Winch Spacer Plates. See the FAQ section below for further information on both of these winches.
Recovery Shackle Tabs
Optional Recovery Shackle Tabs are modeled after the high clearance tabs designed for our hard core BFH series bumpers. These tabs are angle to provide maximum approach angle. They are CNC machined from 1 inch thick steel billet, specifically designed to accept our heavy duty 3/4 inch Recovery Shackles. Selecting this option will get you a pair of these tabs, expertly welded to the Brawler Lite bumper.
Separate versions of the Brawler Lite are available with no bar or with the Brawler Bar.The Brawler Lite comes to you as bare steel, ready to accept paint or powdercoat in the color of your choice. A powdercoat option for this item is Not currently available directly through Poison Spyder.
SKU: 17-59-010-ST-PSC -
Front Bumpers
JK Brawler Lite Front Bumper Trail Stinger Tabs Poison Spyder – 17-59-010-DST
JK Brawler Lite Front Bumper Trail Stinger Tabs for Jeep Wrangler JK 2007-2016. The Brawler Lite front bumper for JK is a grille-width, high clearance bumper designed to combine hard core off-road performance with Full features. This bumper is fabricated from 3/16 inch plate steel, CNC laser-cut and precision brake-formed into a low profile, high clearance design. The ends of the bumper extend far enough to protect the lower corner of the JK grille, but Not far enough to hinder tire clearance or tire access to vertical obstacles. This product ships as bare steel. It will need to be painted or powdercoated prior to final installation. We do Not offer a powdercoat option for this item.
Features:- Compact, multi-faceted design protects lower grille corners while giving tires plenty of clearance and access to climb obstacles
- CNC laser cut from 3/16 plate steel, precision brake-formed for a perfect fit
- Recessed light buckets accept OE fog lamps or Rigid Industries Duallys by use of adapter plate (sold separately)
- Trail Stinger made of 1.5 X .120 wall DOM tubing with 1.25 OD X .120 wall DOM tube gussets
- High clearance recovery shackle tabs CNC machined from 1 thick plate steel
Plate Steel Construction
This bumper is fabricated from 3/16 inch plate steel, CNC laser-cut and precision brake-formed into a low profile, high clearance design. The ends of the bumper extend far enough to protect the lower corner of the JK grille, but Not far enough to hinder tire clearance or tire access to vertical obstacles.
Trail Stinger
The Trail Stinger used on this version of the Brawler Lite is modeled after the famous Trail Stinger originally developed and popularized by Poison Spyder. This time-honored design has proven itself on hundreds of Jeeps over the past decade, providing simple, clean lines along with a measure of forward-flop protection. The Trail Stinger is made of CNC laser-Notched, NC-bent 1.75 inch diameter .120 inch wall DOM tubing.The complex laser-cut Notch allows the Brawler Bar to be welded to two different planes on the surface of the bumper, providing incredible strength. The Trail Stinger is fortified by a pair of 1.25 inch diameter .120 inch wall DOM tube gussets. Note: Warn PowerPlant winches are Not a direct-fit with the DOM Tube gussets (they may be installed with some minor modifications by the installer). Brawler Lite is also available with the Brawler Bar or with no bar/stinger.
Easy Installation
Unlike the Poison Spyder BFH series bumpers for JK, the Brawler Lite can be mounted without cutting or altering the Jeep frame rails. The faceted design of the Brawler Lite provides the best ground clearance and approach angle possible in a bumper that does Not require frame modifications. The factory Crash Bar may be left intact or removed for a sleek appearance and high clearance. If keeping the crash bar, we recommend adding the Brawler Lite Skid Plate (sold separately), which conceals the crash bar and protects the electronic sway bar disconnect.
Recessed Fog Lamp Mounts
Brawler Lite comes with built-in, recessed fog lamp mounts that are designed to easily accept your Stock fog lamps. And these are Not just simple light tabs placed behind a hole in the bumper they are recessed in a bucket made of a Full tubular section to encircle the lamp and keep light from annoyingly leaking behind and around the bumper. Adding further convenience are mounting holes for re-installing the harness retainer clips for the factory wiring, to keep the wiring neatly secured. If you would like a lot more power than the factory fog lamps provide, you can opt to install a set of Rigid Industries Dually or D2 Dually LED lamps using our JK Fog Light Mounts for Rigid Industries Dually/D2.
Important: The Stock fog lamps used on the Jeep Wrangler 10th Anniversary Rubicon do Not fit into the fog lamp buckets on this bumper. If installing this bumper on a 10th Anniversary Rubicon, we suggest using a pair of Rigid Industries Dually or Dually D2 LED lamps along with our JK Dually Fog Lamp Mounts instead of the Stock fog lamps.
Winch Compatibility
The Brawler Lite top-mounted, integrated winch mount is part of the Fully boxed, internally gusseted bumper shell. Winches that are mounted inside the bumper lose this box strength as well as the strength of internal gussets. The Brawler Lite is designed to accept Most Warn and other brand winches that use the popular 10 inch X 4.5 inch mounting pattern, with a few small exceptions. Warn Powerplant winches fit the Brawler Lite with Brawler Bar and Plate Gussets just fine, however it will require slight modifications to use this winch with the Tube Gusset variant. Mounting the Warn Zeon winches requires our Zeon Winch Spacer Plates. See the FAQ section below for further information on both of these winches.
Recovery Shackle Tabs
Optional Recovery Shackle Tabs are modeled after the high clearance tabs designed for our hard core BFH series bumpers. These tabs are angle to provide maximum approach angle. They are CNC machined from 1 inch thick steel billet, specifically designed to accept our heavy duty 3/4 inch Recovery Shackles. Selecting this option will get you a pair of these tabs, expertly welded to the Brawler Lite bumper.
Separate versions of the Brawler Lite are available with no bar or with the Brawler Bar.The Brawler Lite comes to you as bare steel, ready to accept paint or powdercoat in the color of your choice. A powdercoat option for this item is Not currently available directly through Poison Spyder.
SKU: 17-59-010-DST-PSC -
Front Bumper Skid Plates
JK Brawler Lite Front Skid Black Poison Spyder – 17-59-030P1
JK Brawler Lite Front Skid Black for Jeep Wrangler JK 2007-2016. The JK Brawler Lite Front Skid is an optional addition to the JK Brawler Lite front bumper. This skid attaches to the bottom of the Brawler Lite bumper to conceal and protect the Stock crash bar, plus it has an extension to protect the electronic swaybar disconnect motor found on Rubicon JKs. The skid is made of CNC laser-cut 3/16 inch plate steel, precision brake-formed for a precise fit to the Brawler Lite bumper.
Features:- SpyderShell Armor Coat finish with 5-Year Warranty
- Bolts to bottom of Poison Spyder JK Brawler Lite Front Bumpers (sold separately)
- Covers factory crash bar and protects Stock Jeep electrical swaybar disconnect mechanism
- CNC laser cut from 3/16 plate steel
- Precision brake-formed for a perfect fit.
SKU: 17-59-030P1-PSC -
Front Bumper Skid Plates
JK Brawler Lite Front Skid Poison Spyder – 17-59-030
JK Brawler Lite Front Skid for Jeep Wrangler JK 2007-2016. The JK Brawler Lite Front Skid is an optional addition to the JK Brawler Lite front bumper. This skid attaches to the bottom of the Brawler Lite bumper to conceal and protect the Stock crash bar, plus it has an extension to protect the electronic swaybar disconnect motor found on Rubicon JKs. The skid is made of CNC laser-cut 3/16 inch plate steel, precision brake-formed for a precise fit to the Brawler Lite bumper.
Features:- Bolts to bottom of Poison Spyder JK Brawler Lite Front Bumpers (sold separately)
- Covers factory crash bar and protects Stock Jeep electrical swaybar disconnect mechanism
- CNC laser cut from 3/16 plate steel
- Precision brake-formed for a perfect fit
This product ships as bare steel. It will need to be painted or powdercoated prior to final installation. We do Not offer a powdercoat option for this item.
SKU: 17-59-030-PSC -
Front Bumpers
JK Brawler MID Front Bumper Brawler Bar Poison Spyder – 17-63-010-BT
JK Brawler Mid Front Bumper Brawler Bar for Jeep Wrangler JK 2007-2016. The Brawler Mid front bumper for JK is a Mid-width, high clearance bumper designed to combine off-road performance with Full features. This bumper is fabricated from 3/16 inch plate steel, CNC laser-cut and precision brake-formed into a low profile, high clearance design.
The ends of the bumper extend farther outboard than our Brawler Lite bumper, to about half the width of the tires. This provides increased brush protection for the grille corners and fenders, and gives the Jeep a more expeditionary look than our more rock-crawling specific bumpers. This product ships as bare steel it will need to be painted or powdercoated prior to final installation. We do Not offer a powdercoat option for this item.
Features:- Mid-width, multi-faceted design protects lower grille and extends halfway across the front of the tires
- CNC laser cut from 3/16 plate steel, precision brake-formed for a perfect fit
- Recessed light buckets accept OE fog lamps or Rigid Industries Dually’s by use of adapter plate (sold separately)
- Brawler Bar made of 1.5 X .120 wall DOM tubing with 1.25 OD X .120 wall DOM tube gussets
This bumper is fabricated from 3/16 inch plate steel, CNC laser-cut and precision brake-formed into a low profile, high clearance design. The ends of the bumper extend far enough to protect the lower corner of the JK grille, but Not far enough to hinder tire clearance or tire access to vertical obstacles.
Brawler Bar
(This part number is for the Brawler Mid without any Brawler Bar. Click Here for the Brawler Mid with Brawler Bar). The Brawler Bar is modeled after the bar found on our original RockBrawler front bumper. It is a low-profile stinger designed to provide protection to the winch, grille and radiator area. The Brawler Bar is made of CNC laser-Notched, NC-bent 1 3/4 inch diameter .120 inch wall DOM tubing. The complex laser-cut Notch allows the Brawler Bar to be welded to two different planes on the surface of the bumper, providing incredible strength. Two gusset styles are offered for strengthening the Brawler Bar. CNC laser-cut brake-formed 3/16 inch plate steel or CNC laser Notched DOM tubing.Note: Warn PowerPlant winches are Not a direct-fit with the DOM Tube gussets (they may be installed with some minor modifications by the installer).
Easy Installation
Unlike the Poison Spyder BFH series bumpers for JK, the Brawler Mid can be mounted without cutting or altering the Jeep frame rails. The faceted design of the Brawler Mid provides the best ground clearance and approach angle possible in a bumper that doesn’t require frame modifications. The factory Crash Bar may be left intact or removed for a sleek appearance and high clearance. If keeping the crash bar, we recommend adding the Brawler Mid Skid Plate (sold separately), which conceals the crash bar and protects the electronic sway bar disconnect.
Recessed Fog Lamp Mounts
Brawler Mid comes with provisions for re-mounting your factory fog lamps. These consist of recessed fog lamp buckets that are made of CNC laser cut DOM tubing with a mounting flange designed to accept the mounting hardware of the Stock lamps. The recess and all-steel buckets help protect the lamps from the rocks. For those who do Not have the Stock fog lamps, or would like to upgrade to more powerful LED lamps, Poison Spyder offers a unique LED Fog Lamp Mounting Kit for installing a pair of Rigid Industries Dually LED lamps in the fog lamp locations.
Important: The Stock fog lamps used on the Jeep Wrangler 10th Anniversary Rubicon do Not fit into the fog lamp buckets on this bumper. If installing this bumper on a 10th Anniversary Rubicon, we suggest using a pair of Rigid Industries Dually or Dually D2 LED lamps along with our JK Dually Fog Lamp Mounts instead of the Stock fog lamps.
Winch Compatibility
The Brawler Mid bumper is designed to accept Most Warn winches, and winches from other manufacturers that conform to Warn’s Standardized winch mounting dimensions. The winch sits in a slight depression on the top surface of the bumper, with plenty of CNC laser cut plate steel gusseting inside the bumper shell, directly underneath the winch to provide maximum strength.The Winch Fairlead Mount is sold separately, so that those who wish to Not run a winch are left with a clean looking, unobstructed top surface on their bumper. Important: installing the Warn Zeon winch on the Brawler Mid Front Bumper requires Two sets of our Zeon Winch Spacer Plates (p/n 45-57-010-03, sold separately).
Recovery Shackle Tabs
Optional Recovery Shackle Tabs are modeled after the high clearance tabs designed for our hard core BFH series bumpers. These tabs are angle to provide maximum approach angle. They are CNC machined from 1 inch thick steel billet, specifically designed to accept our heavy duty 3/4 inch Recovery Shackles. Selecting this option will get you a pair of these tabs, expertly welded to the Brawler Mid bumper.
Optional Brawler Mid Skid
The optional Brawler Mid Skid attaches to the bottom of the Brawler Mid bumper to conceal and protect the Stock crash bar, plus it has an extension to protect the electronic swaybar disconnect motor found on Rubicon JKs.The skid is made of CNC laser-cut 3/16 inch plate steel, precision brake-formed for a precise fit to the Brawler Mid front bumper.
A separate version of the Brawler Mid is available without the Brawler Bar. The Brawler Mid comes to you as bare steel, ready to accept paint or powdercoat in the color of your choice. A powdercoat option for this item is Not currently available directly through Poison Spyder. See your nearest Poison Spyder dealer for powdercoating options through a coating shop near you.SKU: 17-63-010-BT-PSC -
Front Bumpers
JK Brawler MID Front Bumper Brawler Bar Tabs Black Poison Spyder – 17-63-010-DBTP1
JK Brawler Mid Front Bumper Brawler Bar Tabs Black for Jeep Wrangler JK 2007-2016. The Brawler Mid front bumper for JK is a Mid-width, high clearance bumper designed to combine off-road performance with Full features. This bumper is fabricated from 3/16 inch plate steel, CNC laser-cut and precision brake-formed into a low profile, high clearance design.
The ends of the bumper extend farther outboard than our Brawler Lite bumper, to about half the width of the tires. This provides increased brush protection for the grille corners and fenders, and gives the Jeep a more expeditionary look than our more rock-crawling specific bumpers. This product ships as bare steel it will need to be painted or powdercoated prior to final installation. We do Not offer a powdercoat option for this item.
Features:- SpyderShell Armor Coat finish with 5-Year Warranty
- Mid-width, multi-faceted design protects lower grille and extends halfway across the front of the tires
- CNC laser cut from 3/16 plate steel, precision brake-formed for a perfect fit
- Recessed light buckets accept OE fog lamps or Rigid Industries Duallys by use of adapter plate (sold separately)
- Brawler Bar made of 1.5 X .120 wall DOM tubing with 1.25 OD X .120 wall DOM tube gussets
This bumper is fabricated from 3/16 inch plate steel, CNC laser-cut and precision brake-formed into a low profile, high clearance design. The ends of the bumper extend far enough to protect the lower corner of the JK grille, but Not far enough to hinder tire clearance or tire access to vertical obstacles.
Brawler Bar
(This part number is for the Brawler Mid without any Brawler Bar. Click Here for the Brawler Mid with Brawler Bar). The Brawler Bar is modeled after the bar found on our original RockBrawler front bumper. It is a low-profile stinger designed to provide protection to the winch, grille and radiator area. The Brawler Bar is made of CNC laser-Notched, NC-bent 1 3/4 inch diameter .120 inch wall DOM tubing. The complex laser-cut Notch allows the Brawler Bar to be welded to two different planes on the surface of the bumper, providing incredible strength. Two gusset styles are offered for strengthening the Brawler Bar. CNC laser-cut brake-formed 3/16 inch plate steel or CNC laser Notched DOM tubing.Note: Warn PowerPlant winches are Not a direct-fit with the DOM Tube gussets (they may be installed with some minor modifications by the installer).
Easy Installation
Unlike the Poison Spyder BFH series bumpers for JK, the Brawler Mid can be mounted without cutting or altering the Jeep frame rails. The faceted design of the Brawler Mid provides the best ground clearance and approach angle possible in a bumper that does not require frame modifications. The factory Crash Bar may be left intact or removed for a sleek appearance and high clearance. If keeping the crash bar, we recommend adding the Brawler Mid Skid Plate (sold separately), which conceals the crash bar and protects the electronic sway bar disconnect.
Recessed Fog Lamp Mounts
Brawler Mid comes with provisions for re-mounting your factory fog lamps. These consist of recessed fog lamp buckets that are made of CNC laser cut DOM tubing with a mounting flange designed to accept the mounting hardware of the Stock lamps. The recess and all-steel buckets help protect the lamps from the rocks. For those who do Not have the Stock fog lamps, or would like to upgrade to more powerful LED lamps, Poison Spyder offers a unique LED Fog Lamp Mounting Kit for installing a pair of Rigid Industries Dually LED lamps in the fog lamp locations.
Important: The Stock fog lamps used on the Jeep Wrangler 10th Anniversary Rubicon do Not fit into the fog lamp buckets on this bumper. If installing this bumper on a 10th Anniversary Rubicon, we suggest using a pair of Rigid Industries Dually or Dually D2 LED lamps along with our JK Dually Fog Lamp Mounts instead of the Stock fog lamps.
Winch Compatibility
The Brawler Mid bumper is designed to accept Most Warn winches, and winches from other manufacturers that conform to Warn Standardized winch mounting dimensions. The winch sits in a slight depression on the top surface of the bumper, with plenty of CNC laser cut plate steel gusseting inside the bumper shell, directly underneath the winch to provide maximum strength.The Winch Fairlead Mount is sold separately, so that those who wish to Not run a winch are left with a clean looking, unobstructed top surface on their bumper. Important: installing the Warn Zeon winch on the Brawler Mid Front Bumper requires Two sets of our Zeon Winch Spacer Plates (p/n 45-57-010-03, sold separately).
Recovery Shackle Tabs
Optional Recovery Shackle Tabs are modeled after the high clearance tabs designed for our hard core BFH series bumpers. These tabs are angle to provide maximum approach angle. They are CNC machined from 1 inch thick steel billet, specifically designed to accept our heavy duty 3/4 inch Recovery Shackles. Selecting this option will get you a pair of these tabs, expertly welded to the Brawler Mid bumper.
Optional Brawler Mid Skid
The optional Brawler Mid Skid attaches to the bottom of the Brawler Mid bumper to conceal and protect the Stock crash bar, plus it has an extension to protect the electronic swaybar disconnect motor found on Rubicon JKs.The skid is made of CNC laser-cut 3/16 inch plate steel, precision brake-formed for a precise fit to the Brawler Mid front bumper.
A separate version of the Brawler Mid is available without the Brawler Bar. The Brawler Mid comes to you as bare steel, ready to accept paint or powdercoat in the color of your choice. A powdercoat option for this item is Not currently available directly through Poison Spyder.SKU: 17-63-010-DBTP1-PSC -
Front Bumpers
JK Brawler MID Front Bumper Brawler Bar Tabs Poison Spyder – 17-63-010-DBT
JK Brawler Mid Front Bumper Brawler Bar Tabs for Jeep Wrangler JK 2007-2016. The Brawler Mid front bumper for JK is a Mid-width, high clearance bumper designed to combine off-road performance with Full features. This bumper is fabricated from 3/16 inch plate steel, CNC laser-cut and precision brake-formed into a low profile, high clearance design.
The ends of the bumper extend farther outboard than our Brawler Lite bumper, to about half the width of the tires. This provides increased brush protection for the grille corners and fenders, and gives the Jeep a more expeditionary look than our more rock-crawling specific bumpers. This product ships as bare steel it will need to be painted or powdercoated prior to final installation. We do Not offer a powdercoat option for this item.
Features:- Mid-width, multi-faceted design protects lower grille and extends halfway across the front of the tires
- CNC laser cut from 3/16 plate steel, precision brake-formed for a perfect fit
- Brawler Bar made of 1.5 X .120 wall DOM tubing with 1.25 OD X .120 wall DOM tube gussets
- High clearance recovery shackle tabs CNC machined from 1 thick plate steel
This bumper is fabricated from 3/16 inch plate steel, CNC laser-cut and precision brake-formed into a low profile, high clearance design. The ends of the bumper extend far enough to protect the lower corner of the JK grille, but Not far enough to hinder tire clearance or tire access to vertical obstacles.
Brawler Bar
(This part number is for the Brawler Mid without any Brawler Bar. Click Here for the Brawler Mid with Brawler Bar). The Brawler Bar is modeled after the bar found on our original RockBrawler front bumper. It is a low-profile stinger designed to provide protection to the winch, grille and radiator area. The Brawler Bar is made of CNC laser-Notched, NC-bent 1.75 inch diameter .120 inch wall DOM tubing. The complex laser-cut Notch allows the Brawler Bar to be welded to two different planes on the surface of the bumper, providing incredible strength. Two gusset styles are offered for strengthening the Brawler Bar. CNC laser-cut brake-formed 3/16 inch plate steel or CNC laser Notched DOM tubing.Note: Warn PowerPlant winches are Not a direct-fit with the DOM Tube gussets (they may be installed with some minor modifications by the installer).
Easy Installation
Unlike the Poison Spyder BFH series bumpers for JK, the Brawler Mid can be mounted without cutting or altering the Jeep frame rails. The faceted design of the Brawler Mid provides the best ground clearance and approach angle possible in a bumper that does Not require frame modifications. The factory Crash Bar may be left intact or removed for a sleek appearance and high clearance. If keeping the crash bar, we recommend adding the Brawler Mid Skid Plate (sold separately), which conceals the crash bar and protects the electronic sway bar disconnect.
Recessed Fog Lamp Mounts
Brawler Mid comes with provisions for re-mounting your factory fog lamps. These consist of recessed fog lamp buckets that are made of CNC laser cut DOM tubing with a mounting flange designed to accept the mounting hardware of the Stock lamps. The recess and all-steel buckets help protect the lamps from the rocks. For those who do Not have the Stock fog lamps, or would like to upgrade to more powerful LED lamps, Poison Spyder offers a unique LED Fog Lamp Mounting Kit for installing a pair of Rigid Industries Dually LED lamps in the fog lamp locations.
Important: The Stock fog lamps used on the Jeep Wrangler 10th Anniversary Rubicon do Not fit into the fog lamp buckets on this bumper. If installing this bumper on a 10th Anniversary Rubicon, we suggest using a pair of Rigid Industries Dually or Dually D2 LED lamps along with our JK Dually Fog Lamp Mounts instead of the Stock fog lamps.
Winch Compatibility
The Brawler Mid bumper is designed to accept Most Warn winches, and winches from other manufacturers that conform to Warn Standardized winch mounting dimensions. The winch sits in a slight depression on the top surface of the bumper, with plenty of CNC laser cut plate steel gusseting inside the bumper shell, directly underneath the winch to provide maximum strength.The Winch Fairlead Mount is sold separately, so that those who wish to Not run a winch are left with a clean looking, unobstructed top surface on their bumper. Important: installing the Warn Zeon winch on the Brawler Mid Front Bumper requires Two sets of our Zeon Winch Spacer Plates (p/n 45-57-010-03, sold separately).
Recovery Shackle Tabs
Optional Recovery Shackle Tabs are modeled after the high clearance tabs designed for our hard core BFH series bumpers. These tabs are angle to provide maximum approach angle. They are CNC machined from 1 inch thick steel billet, specifically designed to accept our heavy duty 3/4 inch Recovery Shackles. Selecting this option will get you a pair of these tabs, expertly welded to the Brawler Mid bumper.
Optional Brawler Mid Skid
The optional Brawler Mid Skid attaches to the bottom of the Brawler Mid bumper to conceal and protect the Stock crash bar, plus it has an extension to protect the electronic swaybar disconnect motor found on Rubicon JKs.The skid is made of CNC laser-cut 3/16 inch plate steel, precision brake-formed for a precise fit to the Brawler Mid front bumper.
A separate version of the Brawler Mid is available without the Brawler Bar. The Brawler Mid comes to you as bare steel, ready to accept paint or powdercoat in the color of your choice. A powdercoat option for this item is Not currently available directly through Poison Spyder. See your nearest Poison Spyder dealer for powdercoating options through a coating shop near you.SKU: 17-63-010-DBT-PSC -
Front Bumpers
JK Brawler MID Front Bumper Poison Spyder – 17-63-010
JK Brawler Mid Front Bumper for Jeep Wrangler JK 2007-2016. The Brawler Mid front bumper for JK is a Mid-width, high clearance bumper designed to combine off-road performance with Full features. This bumper is fabricated from 3/16 inch plate steel, CNC laser-cut and precision brake-formed into a low profile, high clearance design.
The ends of the bumper extend farther outboard than our Brawler Lite bumper, to about half the width of the tires. This provides increased brush protection for the grille corners and fenders, and gives the Jeep a more expeditionary look than our more rock-crawling specific bumpers. This product ships as bare steel. It will need to be painted or powdercoated prior to final installation. We do Not offer a powdercoat option for this item.
Features:- Mid-width, multi-faceted design protects lower grille and extends halfway across the front of the tires
- CNC laser cut from 3/16 plate steel, precision brake-formed for a perfect fit
- Recessed light buckets accept OE fog lamps or Rigid Industries Duallys by use of adapter plate (sold separately)
- Plate Steel Construction
This bumper is fabricated from 3/16 inch plate steel, CNC laser-cut and precision brake-formed into a low profile, high clearance design. The ends of the bumper extend far enough to protect the lower corner of the JK grille, but Not far enough to hinder tire clearance or tire access to vertical obstacles.
Brawler Bar
(This part number is for the Brawler Mid without any Brawler Bar. Click Here for the Brawler Mid with Brawler Bar). The Brawler Bar is modeled after the bar found on our original RockBrawler front bumper. It is a low-profile stinger designed to provide protection to the winch, grille and radiator area. The Brawler Bar is made of CNC laser-Notched, NC-bent 1.75 inch diameter .120 inch wall DOM tubing. The complex laser-cut Notch allows the Brawler Bar to be welded to two different planes on the surface of the bumper, providing incredible strength. Two gusset styles are offered for strengthening the Brawler Bar. CNC laser-cut brake-formed 3/16 inch plate steel or CNC laser Notched DOM tubing.Note: Warn PowerPlant winches are Not a direct-fit with the DOM Tube gussets (they may be installed with some minor modifications by the installer).
Easy Installation
Unlike the Poison Spyder BFH series bumpers for JK, the Brawler Mid can be mounted without cutting or altering the Jeep frame rails. The faceted design of the Brawler Mid provides the best ground clearance and approach angle possible in a bumper that doesn’t require frame modifications. The factory Crash Bar may be left intact or removed for a sleek appearance and high clearance. If keeping the crash bar, we recommend adding the Brawler Mid Skid Plate (sold separately), which conceals the crash bar and protects the electronic sway bar disconnect.
Recessed Fog Lamp Mounts
Brawler Mid comes with provisions for re-mounting your factory fog lamps. These consist of recessed fog lamp buckets that are made of CNC laser cut DOM tubing with a mounting flange designed to accept the mounting hardware of the Stock lamps. The recess and all-steel buckets help protect the lamps from the rocks. For those who do Not have the Stock fog lamps, or would like to upgrade to more powerful LED lamps, Poison Spyder offers a unique LED Fog Lamp Mounting Kit for installing a pair of Rigid Industries Dually LED lamps in the fog lamp locations.
Important: The Stock fog lamps used on the Jeep Wrangler 10th Anniversary Rubicon do Not fit into the fog lamp buckets on this bumper. If installing this bumper on a 10th Anniversary Rubicon, we suggest using a pair of Rigid Industries Dually or Dually D2 LED lamps along with our JK Dually Fog Lamp Mounts instead of the Stock fog lamps.
Winch Compatibility
The Brawler Mid bumper is designed to accept Most Warn winches, and winches from other manufacturers that conform to Warn Standardized winch mounting dimensions. The winch sits in a slight depression on the top surface of the bumper, with plenty of CNC laser cut plate steel gusseting inside the bumper shell, directly underneath the winch to provide maximum strength.The Winch Fairlead Mount is sold separately, so that those who wish to Not run a winch are left with a clean looking, unobstructed top surface on their bumper. Important: installing the Warn Zeon winch on the Brawler Mid Front Bumper requires Two sets of our Zeon Winch Spacer Plates (p/n 45-57-010-03, sold separately).
Recovery Shackle Tabs
Optional Recovery Shackle Tabs are modeled after the high clearance tabs designed for our hard core BFH series bumpers. These tabs are angle to provide maximum approach angle. They are CNC machined from 1 thick steel billet, specifically designed to accept our heavy duty 3/4 inch Recovery Shackles. Selecting this option will get you a pair of these tabs, expertly welded to the Brawler Mid bumper.
Optional Brawler Mid Skid
The optional Brawler Mid Skid attaches to the bottom of the Brawler Mid bumper to conceal and protect the Stock crash bar, plus it has an extension to protect the electronic swaybar disconnect motor found on Rubicon JKs.The skid is made of CNC laser-cut 3/16 inch plate steel, precision brake-formed for a precise fit to the Brawler Mid front bumper.
A separate version of the Brawler Mid is available without the Brawler Bar. The Brawler Mid comes to you as bare steel, ready to accept paint or powdercoat in the color of your choice. A powdercoat option for this item is Not currently available directly through Poison Spyder. See your nearest Poison Spyder dealer for powdercoating options through a coating shop near you.SKU: 17-63-010-PSC -
Front Bumper Skid Plates
JK Brawler MID Front Skid Black Poison Spyder – 17-63-030P1
JK Brawler Mid Front Skid Black for Jeep Wrangler JK 2007-2016. The JK Brawler Mid Front Skid is an optional addition to the JK Brawler Mid Front Bumper. This skid attaches to the bottom of the Brawler Mid bumper to conceal and protect the Stock crash bar, plus it has an extension to protect the electronic swaybar disconnect motor found on Rubicon JKs. The skid is made of CNC laser-cut 3/16 inch plate steel, precision brake-formed for a precise fit to the Brawler Mid front bumper.
This product ships as powdercoated black.
Features:- Bolts to bottom of Poison Spyder JK Brawler Mid Front Bumpers (sold separately)
- Covers factory crash bar and protects Stock Jeep electrical swaybar disconnect mechanism
- CNC laser cut from 3/16 plate steel
- Precision brake-formed for a perfect fit
SKU: 17-63-030P1-PSC -
Front Bumper Skid Plates
JK Brawler MID Front Skid Poison Spyder – 17-63-030
JK Brawler Mid Front Skid for Jeep Wrangler JK 2007-2016. The JK Brawler Mid Front Skid is an optional addition to the JK Brawler Mid Front Bumper. This skid attaches to the bottom of the Brawler Mid bumper to conceal and protect the Stock crash bar, plus it has an extension to protect the electronic swaybar disconnect motor found on Rubicon JKs. The skid is made of CNC laser-cut 3/16 inch plate steel, precision brake-formed for a precise fit to the Brawler Mid front bumper.
This product ships as bare steel. It will need to be painted or powdercoated prior to final installation. We do Not offer a powdercoat option for this item.
Features:- Bolts to bottom of Poison Spyder JK Brawler Mid Front Bumpers (sold separately)
- Covers factory crash bar and protects Stock Jeep electrical swaybar disconnect mechanism
- CNC laser cut from 3/16 plate steel
- Precision brake-formed for a perfect fit
SKU: 17-63-030-PSC -
Front Bumpers
JK Front Bumper Kit Epic 07-Pres Wrangler JK TeraFlex
%3Cp%3EThe+TeraFlex+JK+Epic+front+bumper+with+offset+drum+winch+is+designed+to+offer+ultimate+rock+protection+and+compliment+the+JK+body+with+an+attractive+eye-catching+style+that+will+keep+heads+turning%21%3Cbr+%2F%3E%3Cstrong%3EFits%3A%3C%2Fstrong%3E%3C%2Fp%3E%0A%3Cul%3E%0A%3Cli%3E07-Present+Jeep+Wrangler+JK%3C%2Fli%3E%0A%3Cli%3E07-Present+Jeep+Wrangler+Unlimited+JK%3C%2Fli%3E%0A%3C%2Ful%3E%0A%3Cp%3E%3Cstrong%3EDetails%3A%3C%2Fstrong%3E%3C%2Fp%3E%0A%3Cul%3E%0A%3Cli%3ERecessed+mounting+allows+more+grill+space+for+taller+winches+and+increased+radiator+air+flow%3C%2Fli%3E%0A%3Cli%3EWinch+mount+integrated+into+bumper+design%3C%2Fli%3E%0A%3Cli%3EFits+all+major+winch+models+w%2Foffset+bolt+pattern+including+larger+Warn+Powerplant%3C%2Fli%3E%0A%3Cli%3ESteel+w%2Ftextured+black+powder+coat+finish%3C%2Fli%3E%0A%3Cli%3E100+Percent+bolt-on+install+in+2.5+hours%3C%2Fli%3E%0A%3Cli%3EFactory+fog+lights+retain+factory+style+and+technology%3C%2Fli%3E%0A%3Cli%3E2012%2B+JK+Wranglers+need+Vacuum+Pump+Relocation+Bracket+P%2FN+4403100%3C%2Fli%3E%0A%3Cli%3ELifetime+defect+warranty%2F90+day+powder+coat+warranty%3C%2Fli%3E%0A%3C%2Ful%3E%0A
SKU: 4653100-FNNT -
Front Bumpers
JK Front Bumper Kit Epic Center Mount Winch 07-Pres Wrangler JK TeraFlex
%3Cp%3EThe+TeraFlex+JK+Epic+front+bumper+with+center+drum+winch+is+designed+to+offer+ultimate+rock+protection+and+compliment+the+JK+body+with+an+attractive+eye-catching+style+that+will+keep+heads+turning%21%3Cbr+%2F%3E%3Cstrong%3EFits%3A%3C%2Fstrong%3E%3C%2Fp%3E%0A%3Cul%3E%0A%3Cli%3E07-Present+Jeep+Wrangler+JK%3C%2Fli%3E%0A%3Cli%3E07-Present+Jeep+Wrangler+Unlimited+JK%3C%2Fli%3E%0A%3C%2Ful%3E%0A%3Cp%3E%3Cstrong%3EDetails%3A%3C%2Fstrong%3E%3C%2Fp%3E%0A%3Cul%3E%0A%3Cli%3ERecessed+mounting+allows+more+grill+space+for+taller+winches+and+increased+radiator+air+flow%3C%2Fli%3E%0A%3Cli%3EWinch+mount+integrated+into+bumper+design%3C%2Fli%3E%0A%3Cli%3EFits+all+major+winch+models+w%2Fcenter+bolt+pattern+including+larger+Warn+Powerplant%3C%2Fli%3E%0A%3Cli%3ESteel+w%2Ftextured+black+powder+coat+finish%3C%2Fli%3E%0A%3Cli%3E100+Percent+bolt-on+install+in+2.5+hours%3C%2Fli%3E%0A%3Cli%3EFactory+fog+lights+retain+factory+style+and+technology%3C%2Fli%3E%0A%3Cli%3E2012%2B+JK+Wranglers+need+Vacuum+Pump+Relocation+Bracket+P%2FN+4403100%3C%2Fli%3E%0A%3Cli%3ELifetime+defect+warranty%2F90+day+powder+coat+warranty%3C%2Fli%3E%0A%3C%2Ful%3E%0A
SKU: 4653200-FNNT -
Front Bumpers
JK Front Bumper Kit Explorer 07-Pres Wrangler JK TeraFlex
%3Cp%3EThe+TeraFlex+JK+front+Explorer+bumper+is+designed+as+an+ultra-minimal+but+functional+accessory.+andnbsp%3BThis+bumper+will+fit+all+major+winch+models+with+standard+bolt+pattern%2C+including+the+larger+Warn+Powerplant.+andnbsp%3BIntegrated+D-Ring+mounts+aid+with+recovery+equipment.+The+Explorer+bumper+also+allows+the+use+of+the+factory+fog+lights+to+retain+factory+styling+and+technology.%3Cbr+%2F%3E%3Cstrong%3EFits%3A%3C%2Fstrong%3E%3C%2Fp%3E%0A%3Cul%3E%0A%3Cli%3E07-Present+Jeep+Wrangler+JK%3C%2Fli%3E%0A%3Cli%3E07-Present+Jeep+Wrangler+Unlimited+JK%3C%2Fli%3E%0A%3C%2Ful%3E%0A%3Cp%3E%3Cstrong%3EDetails%3A%3C%2Fstrong%3E%3C%2Fp%3E%0A%3Cul%3E%0A%3Cli%3ED-rings+mount+from+inside+or+outside+of+bumper%3C%2Fli%3E%0A%3Cli%3ESteel+w%2Ftextured+black+powder+coat+finish%3C%2Fli%3E%0A%3Cli%3E100+Percent+bolt-on+install+in+1.5+hours%3C%2Fli%3E%0A%3Cli%3EFactory+fog+lights+retain+factory+style+and+technology%3C%2Fli%3E%0A%3Cli%3ELifetime+defect+warranty%2F90+day+powder+coat+warranty%3C%2Fli%3E%0A%3C%2Ful%3E%0A
SKU: 4653120-FNNT -
Tire Carriers
JK HD Aluminum Hinged Carrier Kit 07-Pres Wrangler JK TeraFlex
%3Cp%3EThe+TeraFlex+JK+heavy+duty+hinged+carrier+kit+is+designed+to+support+up+to+a+37+inch+tire+over+the+most+extreme+trails+and+obstacles%2C+and+provide+easy+and+immediate+access+to+the+rear+cargo+area+with+a+one-handed+single+action.+The+TeraFlex+heavy+duty+hinged+carrier+spreads+the+load+and+weight+of+the+tire+to+more+than+just+one+hinge+point.+Incorporating+and+using+the+factory+tailgate+hinge+mounting+points+spread+and+separate+the+load+as+far+apart+as+possible%2C+resulting+in+maximum+strength+and+durability.+Dedicated+tooling+provides+a+cast+A356.2+T6+Aluminum+main+component.+This+keeps+the+carrier+as+light%2C+and+strong+as+possible.+The+fit+and+finish+is+designed+to+follow+the+flow+and+contour+of+the+Jeep+body%2C+while+seamlessly+providing+additional+mounting+points+for+off+road+accessories+such+as+recovery+jack+and+fluid+containers.+The+factory+Jeep+body+provides+substantial+internal+gussets+and+bracing+that+easily+supports+the+new+tire+carrier+and+oversized+tire.+The+HD+hinge+brackets+are+forged+steel+and+the+HD+5%2F8+inch+hinge+pins+are+constructed+from+cold+formed+high-carbon+hardened+steel.+The+combination+of+mounting+location+and+HD+mounting+brackets+provides+one+of+the+strongest%2C+rattle-free+tire+carriers+on+the+market+today.+The+TeraFlex+HD+tire+carrier+removes+all+stress+from+the+gate+by+utilizing+the+HD+reinforcement+carrier+as+the+load-carrying+component%3B+in+effect+it+carries+the+weight+of+the+tailgate+assembly+and+the+spare+tire.+The+simple+bolt-on+installation+can+be+performed+using+common+hand+tools%2C+with+no+drilling+required.+The+simple+design+also+allows+for+the+use+of+a+rear+bumper+of+your+choice+-+no+aftermarket+bumper+purchase+is+required%2C+and+it+works+with+most+aftermarket+bumpers.+This+carrier+is+a+patented+design+number+D698224+covered+by+the+USPTO.%3Cbr+%2F%3E%3Cstrong%3EFits%3A%3C%2Fstrong%3E%3C%2Fp%3E%0A%3Cul%3E%0A%3Cli%3E07-Present+Jeep+Wrangler+JK%3C%2Fli%3E%0A%3Cli%3E07-Present+Jeep+Wrangler+Unlimited+JK%3C%2Fli%3E%0A%3C%2Ful%3E%0A%3Cp%3E%3Cstrong%3EDetails%3A%3C%2Fstrong%3E%3C%2Fp%3E%0A%3Cul%3E%0A%3Cli%3EThe+Original+Hinged+HD+Tire+Carrier%3C%2Fli%3E%0A%3Cli%3EA356.2+Cast+Aluminum+Main+Component%3C%2Fli%3E%0A%3Cli%3EBolt-On+Installation%3C%2Fli%3E%0A%3Cli%3ENo+Drilling+Required%3C%2Fli%3E%0A%3Cli%3EBlack+Powdercoat+Finish%3C%2Fli%3E%0A%3C%2Ful%3E%0A
SKU: 4838100-FNNT