Poison Spyder
Showing 1–32 of 153 results
-
Brake lights
2-1/2 LED Back-Up Light Clear Poison Spyder – 41-04-300
2.5 Inch LED Back-Up Light Clear. 2.5 inch flush mount LED back-up light for use with Poison Spyder Customs Crusher Corners, Trail Corners or any other manufacturer corner protectors, or anywhere you can cut a 2.75 inch hole in a flat sheetmetal panel. push-in mounting with the included rubber grommet. Sold by each, if you need a pair specify a quantity of 2.
SKU: 41-04-300-PSC -
Brake lights, Wiring and Hardware
2-Pin LED Flasher 76-96 CJ-YJ Poison Spyder – 41-04-262
2-Pin LED Flasher for 1976-1996 Jeep Wrangler CJ-YJ. Electronic flasher to provide proper current intermittent for LED taillights and turn signals in your 1976-1996 Jeep CJ or YJ. Easy to install (instructions included).
SKU: 41-04-262-PSC -
Brake lights
24in LED Back-Up Light Extension Harness (Pair) Poison Spyder – 41-06-020
24 Inch Back-Up Light Extension Harness (Pair). Poison Spyder JK LED Taillight Harness system is the easy, plug-and-play answer to getting all of your Jeep Wrangler JKs rear LED lighting working quickly and correctly. It is designed to connect directly to your Jeep OE wiring harness, and directly to LED taillights, back-up lights, and license plate lights sold by Poison Spyder.
Exclusive Plug-N-Play Design
Poison Spyder wiring harness system is designed to take all of the guesswork, hassle and labor out of wiring aftermarket LED taillights, back-up lights and license plate/third brake lights on your 2007 and later Jeep Wrangler JK. The two main harness components, to which the other components connect in order to accommodate your Jeep customized rear lighting setup. The JK LED Taillight HarnessDriver Side is typically used on the driver side and does Not include provisions for the license plate light. The JK LED Taillight Harness – Passenger Side is typically used on the passenger side, and includes a 6-foot lead and weatherproof connector for our LED License Plate and 3rd Brake Light – PSC Connectors. You will need two of these JK LED Taillight Harnesses, typically one of each type, for Most configurations. Each of these Taillight Harnesses plug right into your Jeep factory wiring harnesssimply unplug the Stock taillight pigtail and plug the Poison Spyder taillight harness in its place. OEM quality connectors provide a positive, weather-tight connection just like the factory wiring. Weatherproof connectors are used for all other connections as well as automotive quality wires and split-loom protective sheathing. Once the Poison Spyder taillight harnesses are in place, several LED lighting products may be plugged directly into the harness or connected via jumper harnesses.
Supports 4 inch Round LED Taillights
Both driver and passenger side Poison Spyder taillight harnesses include the correct 3-prong connector to plug directly into the 4 inch Round, 24-diode LED Stop/Turn/Tail Lights sold by Poison Spyder. Each taillight harness also incorporates a load resistor to simulate the correct power load so turn signals will flash at the correct speed and to keep the vehicle computer from throwing an error code. No longer must these load resistors be wired in separately with wire taps and butt connectors.Note: The LED taillight connector is designed to work with the 4 inch round LED Taillights sold by Poison Spyder only. It is Not guaranteed to fit any other brand or model of taillight.
Supports 2.5 inch Round LED Back-Up Lamps
Both driver and passenger side Poison Spyder taillight harnesses include Two weather-tight connectors for connecting up to two 2.5 inch Round LED Back-Up Lamps per side, for a total of four such lamps. Typical configurations using Poison Spyder JK Crusher Corners and/or bumpers may include such Back-Up Lamps directly below each LED taillight, in the recessed Back-Up Lamp buckets found on many of our rear bumpers, or both. To connect to Back-Up Lamps located directly below the LED taillights on Poison Spyder JK Crusher Corners, simply use the 4 inch Back-Up Light Extension Harness on each side.To connect to Back-Up Lamps located in the recessed mounts on many Poison Spyder JK Rear Bumpers, use the 24 Inch Back-Up Light Extension Harness on each side. Remember, there are two Back-Up Lamp connectors on each taillight harness, in order to accommodate both a 4 inch and a 24 Inch Back-Up Light Extension Harness on each side simultaneously. Both of these connectors are wired into the vehicle back-up lamp circuit. If you wish to divert one pair of these lamps to use as manually switched load or work lights, you’ll have to research and make the necessary alterations to the harness and the vehicle wiring on your own.
Note: The LED Back-Up Lamp Extension Harnesses are designed to work with the 2.5 Round LED Back-Up Lamps sold by Poison Spyder only. They are Not guaranteed to fit any other brand or model of lamp.
Supports LED License Plate and Third Brake Light
The passenger side Poison Spyder taillight harness includes a 6-foot lead with weather-tight connector to connect to our LED License Plate and 3rd Brake Light – PSC Connectors. On Most Jeep JKs on which Poison Spyder Crusher Corners and LED taillights have been installed, the license plate has been relocated from the Stock position on the driver side corner. In Most cases it has been relocated either to the spare tire carrier or to the center of the tailgate on those Jeeps where the spare tire has been removed altogether.In either case, the 6-foot lead on the passenger side LED taillight harness can be routed either through the tailgate or along the tire carrier, and plugged into the LED License Plate and Third Brake Light at the relocated license plate. On those Jeeps where no license plate light is needed or it has already been addressed elsewhere, the lead for the license plate light can be simply coiled up and secured inside the Jeep body corner cavity, secured with some zip-ties.
Note: The license plate lead is designed to work with the LED License Plate and 3rd Brake Light PSC Connectors sold by Poison Spyder only. It is Not guaranteed to fit any other brand or model of license plate light or third brake light.
SKU: 41-06-020-PSC -
Tire Carriers
3-Way Spare Tire Strap Poison Spyder – 57-63-001
The Poison Spyder 3-Way Spare Tire Strap securely holds the spare tire in place during the Most rigorous four-wheeling. This strap was designed for use with the Poison Spyder Rear Stinger Tire Carrier, but can be used with other DIY-fabricated spare tire mounts or to simply tie the spare tire down into the bed of the vehicle.
The use of a strap allows virtually infinite adjustability for any size tire, while allowing quick, easy access to the spare tire without having to use any extra tools. All of these reasons are why similar straps are routinely used for spare tire hold-down duty in off-road racing.
Heavy duty ratchet lets you easily adjust, tighten and release tension. Made of high quality nylon webbing with an embroidered Poison Spyder tag.SKU: 57-63-001-PSC -
Side Marker Lights
3/4 LED Marker Lamp 3-Wire Amber Poison Spyder – 41-04-085
3/4 LED Marker Lamp 3-Wire Amber. 3/4 inch round, Amber lens LED lamp for use as a combination turn signal and running lamp, for use with Poison Spyder Customs DeFenders, Tube Fenders, Crusher Flares, or anywhere you’d like to mount them by drilling a 3/4 inch hole in a flat panel. This is a 3-WIRE assembly, meaning it can be used as both a turn signal And a marker lamp simultaneously.
It can also be used as only a marker lamp (or only a turn signal) by using two wires and leaving the third wire unused. These high quality LED lamps are DOT-approved for use on your vehicle. Includes pigtail harness and mounting grommet. Sold each (select a quantity of 2 if you need a pair).
This item is also available in red or clear/amber.
Important: This item is Not intended as a direct replacement for any Stock turn signal or marker lamp. It does Not plug directly into the vehicle wiring harness it will require cutting and splicing into the vehicle wiring harness.
Features:- 3/4 high intensity LED
- 3-wire design to function as turn signal, marker lamp, or both
- Amber lens
- Install in any flat panel with a 3/4 hole
Requires cutting and splicing into vehicle wiring harness
SKU: 41-04-085-PSC -
Side Marker Lights
3/4 LED Marker Lamp 3-Wire Clear/Amber Poison Spyder – 41-04-080
3/4 LED Marker Lamp 3-Wire Clear/Amber. 3/4 inch round, Amber lens LED lamp for use as a combination turn signal and running lamp, for use with Poison Spyder Customs DeFenders, Tube Fenders, Crusher Flares, or anywhere you’d like to mount them by drilling a 3/4 inch hole in a flat panel.
This is a 3-WIRE assembly, meaning it can be used as both a turn signal AND a marker lamp simultaneously. It can also be used as only a marker lamp (or only a turn signal) by using two wires and leaving the third wire unused. These high quality LED lamps are DOT-approved for use on your vehicle. Includes pigtail harness and mounting grommet. Sold each (select a quantity of 2 if you need a pair).
This item is also available in red or clear/amber.
Important: This item is Not intended as a direct replacement for any Stock turn signal or marker lamp. It does Not plug directly into the vehicle wiring harness it will require cutting and splicing into the vehicle wiring harness.
Features:- 3/4 high intensity LED
- 3-wire design to function as turn signal, marker lamp, or both
- Clear lens with Amber diode
- Install in any flat panel with a 3/4 hole
- Requires cutting and splicing into vehicle’s wiring harness
SKU: 41-04-080-PSC -
Side Marker Lights
3/4 LED Marker Lamp 3-Wire Red Poison Spyder – 41-04-070
3/4 Inch LED Marker Lamp 3-Wire Red. 3/4 inch round, Amber lens LED lamp for use as a combination turn signal and running lamp, for use with Poison Spyder Customs DeFenders, Tube Fenders, Crusher Flares, or anywhere you would like to mount them by drilling a 3/4 inch hole in a flat panel. This is a 3-Wire assembly, meaning it can be used as both a turn signal And a marker lamp simultaneously. It can also be used as only a marker lamp (or only a turn signal) by using two wires and leaving the third wire unused. These high quality LED lamps are DOT-approved for use on your vehicle. Includes pigtail harness and mounting grommet. Sold each (select a quantity of 2 if you need a pair).
This item is also available in red or clear/amber.
Important: This item is Not intended as a direct replacement for any Stock turn signal or marker lamp. It does Not plug directly into the vehicle wiring harness it will require cutting and splicing into the vehicle wiring harness.
Features:- 3/4 high intensity LED
- 3-wire design to function as turn signal, marker lamp, or both
- Red lens
- Install in any flat panel with a 3/4 inch hole
- Requires cutting and splicing into vehicle wiring harness
SKU: 41-04-070-PSC -
D Ring Shackle
3/4 Recovery Shackle Poison Spyder – 56-16-010
Poison Spyder 3/4 Recovery Shackle. These heavy duty 3/4 inch Recovery Shackles are rated at a working load limit of 4.75 tons. Made of high quality steel and yellow zinc plated for corrosion resistance.
The heavy duty D-ring and massive 7/8 inch threaded pin make a quick job of safely rigging recovery straps and winch cables. No 4X4 should be on the trail without a couple of these in the on board recovery kit. Sold by the piece.SKU: 56-16-010-PSC -
Brake lights
4 24-LED Taillight Push-In with Pigtail & Grommet Clear/Red Poison Spyder – 41-04-051
4 24-LED Taillight Push-In with Pigtail and Grommet Clear/Red. These 24-diode LED taillights easily install using a rubber grommet they simply push into place. This is a 4 inch round light (requires a 4.5 inch hole) with red lens.
Flush-mount LED taillights stay out of the way of rocks and trees on the trail, last longer and shine brighter than OEM incandescent lamps. Available with red or clear lens (make your selection in the options) units with clear lenses use red diodes, so they still flash red when lit up.
These install right into Poison Spyder Customs Crusher Corners or Trail Corners (on units specifically ordered for LED taillights), or can be installed into other manufacturer corner protectors or anywhere you can cut a 4.5 inch round hole in a flat panel.
Includes the LED lamp assembly, rubber grommet and wiring pigtail harness. Sold each (order 2 if you need a pair).SKU: 41-04-051-PSC -
Brake lights
4 24-LED Taillight Push-In with Pigtail & Grommet Red Poison Spyder – 41-04-050
4 24-LED Taillight Push-In with Pigtail and Grommet Red. These 24-diode LED taillights easily install using a rubber grommet they simply push into place. This is a 4 inch round light (requires a 4.5 inch hole) with red lens.
Flush-mount LED taillights stay out of the way of rocks and trees on the trail, last longer and shine brighter than OEM incandescent lamps. Available with red or clear lens (make your selection in the options) units with clear lenses use red diodes, so they still flash red when lit up.
These install right into Poison Spyder Customs Crusher Corners or Trail Corners (on units specifically ordered for LED taillights), or can be installed into other manufacturer corner protectors or anywhere you can cut a 4.5 inch round hole in a flat panel.
Includes the LED lamp assembly, rubber grommet and wiring pigtail harness. Sold each (order 2 if you need a pair).SKU: 41-04-050-PSC -
Brake lights
4 6-LED Taillight Flange Style Poison Spyder – 41-04-036
4 6-LED Taillight Flange Style. 6-diode flush mount LED taillight with red lens for use with Poison Spyder Customs Crusher Corners, Trail Corners or any other manufacturer corner protectors, or anywhere you can cut a 4.5 inch hole in a flat sheet metal panel. Flange-mounting style, red lens.
Sold by each, if you need a pair specify a quantity of 2.
SKU: 41-04-036-PSC -
-
Brake lights
4in LED Back-Up Light Extension Harness (Pair) Poison Spyder – 41-06-030
4in LED Back-Up Light Extension Harness (Pair) Poison Spyder’s JK LED Taillight Harness system is the easy, plug-and-play answer to getting all of your Jeep Wrangler JKs rear LED lighting working quickly and correctly.
It is designed to connect directly to your Jeep OE wiring harness, and directly to LED taillights, back-up lights, and license plate lights sold by Poison Spyder.
Exclusive “Plug-N-Play” Design
Poison Spyder’s wiring harness system is designed to take all of the guesswork, hassle and labor out of wiring aftermarket LED taillights, back-up lights and license plate/third brake lights on your 2007 and later Jeep Wrangler JK. The two main harness components, to which the other components connect in order to accommodate your Jeep customized rear lighting setup. The JK LED Taillight Harness – Driver Side is typically used on the driver’s side and does Not include provisions for the license plate light.The JK LED Taillight Harness – Passenger Side is typically used on the passenger side, and includes a 6-foot lead and weatherproof connector for our LED License Plate & 3rd Brake Light – PSC Connectors. You will need two of these JK LED Taillight Harnesses, typically one of each type, for Most configurations. Each of these Taillight Harnesses plug right into your Jeep factory wiring harnesssimply unplug the Stock taillight pigtail and plug the Poison Spyder taillight harness in its place. OEM quality connectors provide a positive, weather-tight connection just like the factory wiring.
Weatherproof connectors are used for all other connections as well as automotive quality wires and split-loom protective sheathing. Once the Poison Spyder taillight harnesses are in place, several LED lighting products may be plugged directly into the harness or connected via jumper harnesses.
Supports 4″ Round LED Taillights
Both driver and passenger side Poison Spyder taillight harnesses include the correct 3-prong connector to plug directly into the 4″ Round, 24-diode LED Stop/Turn/Tail Lights sold by Poison Spyder. Each taillight harness also incorporates a load resistor to simulate the correct power load so turn signals will flash at the correct speed and to keep the vehicle’s computer from throwing an error code. No longer must these load resistors be wired in separately with wire taps and butt connectors.NotE: The LED taillight connector is designed to work with the 4″ round LED Taillights sold by Poison Spyder only. It is Not guaranteed to fit any other brand or model of taillight.
Supports 2-1/2 inch Round LED Back-Up Lamps
Both driver and passenger side Poison Spyder taillight harnesses include TWO weather-tight connectors for connecting up to two 2-1/2 inch Round LED Back-Up Lamps per side, for a total of four such lamps. Typical configurations using Poison Spyder JK Crusher Corners and/or bumpers may include such Back-Up Lamps directly below each LED taillight, in the recessed Back-Up Lamp buckets found on many of our rear bumpers, or both. To connect to Back-Up Lamps located directly below the LED taillights on Poison Spyder JK Crusher Corners, simply use the 4″ Back-Up Light Extension Harness on each side.To connect to Back-Up Lamps located in the recessed mounts on many Poison Spyder JK Rear Bumpers, use the 24″ Back-Up Light Extension Harness on each side. Remember, there are two Back-Up Lamp connectors on each taillight harness, in order to accommodate both a 4″ and a 24″ Back-Up Light Extension Harness on each side simultaneously. Both of these connectors are wired into the vehicle’s back-up lamp circuit. If you wish to divert one pair of these lamps to use as manually switched load or work lights, you’ll have to research and make the necessary alterations to the harness and the vehicle’s wiring on your own.
Note: The LED Back-Up Lamp Extension Harnesses are designed to work with the 2-1/2 inch Round LED Back-Up Lamps sold by Poison Spyder only. They are Not guaranteed to fit any other brand or model of lamp.
Supports LED License Plate & Third Brake Light
The passenger side Poison Spyder taillight harness includes a 6-foot lead with weather-tight connector to connect to our LED License Plate & 3rd Brake Light – PSC Connectors. On Most Jeep JKs on which Poison Spyder Crusher Corners and LED taillights have been installed, the license plate has been relocated from the Stock position on the driver’s side corner. In Most cases it has been relocated either to the spare tire carrier or to the center of the tailgate on those Jeeps where the spare tire has been removed altogether. In either case, the 6-foot lead on the passenger side LED taillight harness can be routed either through the tailgate or along the tire carrier, and plugged into the LED License Plate & Third Brake Light at the relocated license plate. On those Jeeps where no license plate light is needed or it has already been addressed elsewhere, the lead for the license plate light can be simply coiled up and secured inside the Jeep body’s corner cavity, secured with some zip-tiesNote: The license plate lead is designed to work with the LED License Plate & 3rd Brake Light – PSC Connectors sold by Poison Spyder only. It is Not guaranteed to fit any other brand or model of license plate light or third brake light.
SKU: 41-06-030-PSC -
-
Winch Fairlead
Aluminum Hawse Winch Fairlead Poison Spyder – 45-45-010
The Poison Spyder Aluminum Hawse Fairlead will help protect your synthetic winchline during winch operation, as well as give the front of your 4X4 a little bit of Poison Spyder attitude.
CNC machined from billet aluminum and powdercoated for a durable finish.
Features:- CNC machined from 6061-T6 billet aluminum
- Provides a smooth surface to feed synthetic winch rope through without snags or wear
- Semi-gloss black powdercoat finish
- Poison Spyder logo CNC machined through the powdercoat
- Stainless steel hardware and install instructions included
SKU: 45-45-010-PSC -
Differential Cover
Bombshell Diff Cover Dana 30 Bare – 42-11-030
Bombshell Diff Cover Dana 30 Bare Poison Spyder. Poison Spyder Bombshell Diff Covers are designed to protect your gears, lockers and diff cover bolts from the Most punishing rocks and trail hazards. The Stock covers your Jeep came with are weak, stamped sheet metal. Even a moderate tap with a rock can cave it in against your ring gear, causing potential damage to the gears, locker and carrier bearings, Not to mention a difficult, messy trail fix.
Even more common, though less catastrophic, is peel back that can occur when sliding over a rock causes the lip of the cover to peel up, allowing your gear oil to drain causing a hazard for both your Jeep and the environment.
The Bombshell Diff Cover is your best insurance against each of these hazards.The Dana 30 Bombshell can Now be used on Stock Jeep Wrangler JK and TJ, front or rear axles, with no requirement for aftermarket track bars or suspension modifications! Now you can install the Bombshell Dana 30 Diff Cover on to your bone Stock Jeep, straight off the showroom floor!
This re-design also includes moving the gear oil fill hole to the Stock fluid level height so there is no more research, guesswork or measuringsimply fill the diff to the level of the fill hole.
The Bombshell differential cover is cast from highly ductile nodular iron the same material drag racing differential housings are cast from to handle thousands of horsepower. The design of the Bombshell incorporates recesses to protect the diff cover bolt heads from trail damage, while the profile of the Bombshell acts as a ramp to help slide your Jeep up and over the Most troublesome pumpkin-eaters. The ramp profile also results in an extremely thick and up to 1 inch thickcross-section around the bolt ring, where contact with the rocks is Most likely.Throughout the rest of its cross-section the Bombshell is the thickest cast differential cover on the market, from 7/16 inch to a brutal 1/2 inch thick at the outer most surface.
Installing the Bombshell is fast and easy. Click the icon at left to view our Install Instructions, and view the video on the right to see the installation process. The sealing surface has been CNC machined flat for a perfect seal. Poison Spyder provides a tube of silicon sealant and new Grade 8 hardware so you will have everything you need except for tools and gear oil.
Bombshells are shipped either bare so that you may powdercoat or paint to suit your own preference, or powdercoated semi-gloss black. Note: many of the photos below show where the customer has painted the raised area of the Spyder logo a contrasting color. This is Not done by Poison Spyderour powdercoat option is just a single color (all black).
Features:- Cast nodular iron up to 1/2 inch thick!
- Ramp profile to help slide the vehicle up over rocks
- Recessed bolt heads to protect them from damage
- Grade 8 hardware and silicon sealant included
- bare iron (requires paint or powdercoat)
SKU: 42-11-030-PSC -
Differential Cover
Bombshell Diff Cover Dana 30 Black PC Poison Spyder – 42-11-030-PC
Bombshell Diff Cover Dana 30 Black PC Poison Spyder. Poison Spyder Bombshell Diff Covers are designed to protect your gears, lockers and diff cover bolts from the Most punishing rocks and trail hazards. The Stock covers your Jeep came with are weak, stamped sheet metal. Even a moderate tap with a rock can cave it in against your ring gear, causing potential damage to the gears, locker and carrier bearings, Not to mention a difficult, messy trail fix.
Even more common, though less catastrophic, is peel back that can occur when sliding over a rock causes the lip of the cover to peel up, allowing your gear oil to drain causing a hazard for both your Jeep and the environment.
The Bombshell Diff Cover is your best insurance against each of these hazards.The Dana 30 Bombshell can Now be used on Stock Jeep Wrangler JK and TJ, front or rear axles, with no requirement for aftermarket track bars or suspension modifications! Now you can install the Bombshell Dana 30 Diff Cover on to your bone Stock Jeep, straight off the showroom floor!
This re-design also includes moving the gear oil fill hole to the Stock fluid level height so there’s no more research, guesswork or measuringsimply fill the diff to the level of the fill hole.
The Bombshell differential cover is cast from highly ductile nodular ironthe same material drag racing differential housings are cast from to handle thousands of horsepower. The design of the Bombshell incorporates recesses to protect the diff cover bolt heads from trail damage, while the profile of the Bombshell acts as a ramp to help slide your Jeep up and over the Most troublesome pumpkin-eaters. The ramp profile also results in an extremely thick and up to 1 inch thickcross-section around the bolt ring, where contact with the rocks is Most likely.Throughout the rest of its cross-section the Bombshell is the thickest cast differential cover on the market, from 7/16 inch to a brutal 1/2 inch thick at the outer most surface.
Installing the Bombshell is fast and easy. Click the icon at left to view our Install Instructions, and view the video on the right to see the installation process. The sealing surface has been CNC machined flat for a perfect seal. Poison Spyder provides a tube of silicon sealant and new Grade 8 hardware so you will have everything you need except for tools and gear oil.
Bombshells are shipped either bare so that you may powdercoat or paint to suit your own preference, or powdercoated semi-gloss black. Note: many of the photos below show where the customer has painted the raised area of the Spyder logo a contrasting color. This is Not done by Poison Spyderour powdercoat option is just a single color (all black).
Features:- Cast nodular iron up to 1/2 inch thick!
- Ramp profile to help slide the vehicle up over rocks
- Recessed bolt heads to protect them from damage
- Grade 8 hardware and silicon sealant included
- Semi-gloss black powdercoat finish
SKU: 42-11-030-PC-PSC -
Differential Cover
Bombshell Diff Cover Dana 44 Bare Poison Spyder – 42-11-044
Bombshell Diff Cover Dana 44 Bare. Bombshell Poison Spyder Bombshell Diff Covers are designed to protect your gears, lockers and diff cover bolts from the Most punishing rocks and trail hazards. The Stock covers your Jeep came with are weak, stamped sheet metal. Even a moderate tap with a rock can cave it in against your ring gear, causing potential damage to the gears, locker and carrier bearings, Not to mention a difficult, messy trail fix.
Even more common, though less catastrophic, is peel back that can occur when sliding over a rock causes the lip of the cover to peel up, allowing your gear oil to drain causing a hazard for both your Jeep and the environment. The Bombshell Diff Cover is your best insurance against each of these hazards.
The Dana 44 Bombshell can Now be used on Stock Jeep Wrangler JK and TJ, front or rear axles, with no requirement for aftermarket track bars or suspension modifications! Now you can install the Bombshell Dana 44 Diff Cover on to your bone Stock Jeep, straight off the showroom floor! This re-design also includes moving the gear oil fill hole to the Stock fluid level height so there is no more research, guesswork or measuringsimply fill the diff to the level of the fill hole.The Dana 44 Bombshell differential cover is cast from highly ductile nodular ironthe same material drag racing differential housings are cast from to handle thousands of horsepower. The design of the Bombshell incorporates recesses to protect the diff cover bolt heads from trail damage, while the profile of the Bombshell acts as a ramp to help slide your Jeep up and over the Most troublesome pumpkin-eaters. The ramp profile also results in an extremely thick and up to 1 inch thick cross-section around the bolt ring, where contact with the rocks is Most likely.
Throughout the rest of its cross-section the Bombshell is the thickest cast differential cover on the market, from 7/16 inch to a brutal 1/2 inch thick at the outer most surface.
Installing the Bombshell is fast and easy. The sealing surface has been CNC machined flat for a perfect seal. Poison Spyder provides a tube of silicon sealant and new Grade 8 hardware so you’ll have everything you need except for tools and gear oil.
Bombshells are shipped either bare so that you may powdercoat or paint to suit your own preference, or powdercoated semi-gloss black.
Features:- Cast nodular iron up to 1/2 inch thick!
- Ramp profile to help slide the vehicle up over rocks
- Recessed bolt heads to protect them from damage
- Grade 8 hardware and silicon sealant included
- Semi-gloss black powdercoat finish
SKU: 42-11-044-PSC -
Differential Cover
Bombshell Diff Cover Dana 44 Black PC Poison Spyder – 42-11-044-PC
Bombshell Diff Cover Dana 44 Black PC. Bombshell Poison Spyder Bombshell Diff Covers are designed to protect your gears, lockers and diff cover bolts from the Most punishing rocks and trail hazards. The Stock covers your Jeep came with are weak, stamped sheet metal. Even a moderate tap with a rock can cave it in against your ring gear, causing potential damage to the gears, locker and carrier bearings, Not to mention a difficult, messy trail fix.
Even more common, though less catastrophic, is peel back that can occur when sliding over a rock causes the lip of the cover to peel up, allowing your gear oil to drain causing a hazard for both your Jeep and the environment. The Bombshell Diff Cover is your best insurance against each of these hazards.
The Dana 44 Bombshell can Now be used on Stock Jeep Wrangler JK and TJ, front or rear axles, with no requirement for aftermarket track bars or suspension modifications! Now you can install the Bombshell Dana 44 Diff Cover on to your bone Stock Jeep, straight off the showroom floor! This re-design also includes moving the gear oil fill hole to the Stock fluid level height so there is no more research, guesswork or measuringsimply fill the diff to the level of the fill hole.The Dana 44 Bombshell differential cover is cast from highly ductile nodular ironthe same material drag racing differential housings are cast from to handle thousands of horsepower. The design of the Bombshell incorporates recesses to protect the diff cover bolt heads from trail damage, while the profile of the Bombshell acts as a ramp to help slide your Jeep up and over the Most troublesome pumpkin-eaters. The ramp profile also results in an extremely thick and up to 1 inch thickcross-section around the bolt ring, where contact with the rocks is Most likely.
Throughout the rest of its cross-section the Bombshell is the thickest cast differential cover on the market, from 7/16 inch to a brutal 1/2 inch thick at the outerMost surface.
Installing the Bombshell is fast and easy. The sealing surface has been CNC machined flat for a perfect seal. Poison Spyder provides a tube of silicon sealant and new Grade 8 hardware so you will have everything you need except for tools and gear oil.
Bombshells are shipped either bare so that you may powdercoat or paint to suit your own preference, or powdercoated semi-gloss black.
Features:- Cast nodular iron up to 1/2 inch thick!
- Ramp profile to help slide the vehicle up over rocks
- Recessed bolt heads to protect them from damage
- Grade 8 hardware and silicon sealant included
- Semi-gloss black powdercoat finish
SKU: 42-11-044-PC-PSC -
Roll Cage
Cage Gussets 100-degrees Web (2) Poison Spyder – 43-43-014-W
Cage Gussets 100-degrees Web (2) Poison Spyder. Add strength as well as killer Poison Spyder looks to your cage with these Spyder Web design cage gussets. Gussets are CNC laser-cut from 3/16 inch plate steel.
This part number is for gussets that fit a 100 degree tubing joint. Includes two (2) gussets.SKU: 43-43-014-W-PSC -
Roll Cage
Cage Gussets 90-degrees Web (2) Poison Spyder – 43-43-001-W
Poison Spyder Cage Gussets 90-degrees – Web (2) Add strength as well as killer Poison Spyder looks to your cage with these Spyder Web design cage gussets. Gussets are CNC laser-cut from 3/16 inch plate steel. This part number is for gussets that fit a 90 degree tubing joint.
Includes two (2) gussets.SKU: 43-43-001-W-PSC -
Roll Cage
Cage Gussets Curved Web (2) Poison Spyder – 43-43-011-W
Poison Spyder Cage Gussets Curved – Web (2) Add strength as well as killer Poison Spyder looks to your cage with these Spyder Web design cage gussets. Gussets are CNC laser-cut from 3/16 inch plate steel. This part number is for gussets that fit where a straight tube joins a curved tube, as with the upper B-Pillar joint on Poison Spyder Full Cage Kit
SKU: 43-43-011-W-PSC -
D Ring Shackle
D-Ring Shackle Tab Poison Spyder – 45-42-010
The Poison Spyder D-Ring Shackle Tab allows fabricators to easily add a super-tough recovery attachment point to any structural member of the vehicle. CNC machined from 1 inch thick plate steel, these Shackle Tabs feature chambered edges for maximum weld penetration and a quality, finished appearance.
The tab is specifically designed to accept a 3/4 inch D-ring shackle. Sold by the piece.
Features:- CNC machined from 1 inch thick billet steel
- Provides an extreme duty attachment point for 3/4 inch screw-pin type shackles
- Angled design for the best clearance from rocks when welded to front or rear bumpers
- To be installed by certified welders only
SKU: 45-42-010-PSC -
Rock Sliders
DIY Rico Step Kit 45.25 Poison Spyder – DIY-50-020
DIY Rico Step Kit 45.25 inch. The DIY Rico Step Kit from Poison Spyder allows the do-it-yourselfer to add a heavy duty rub rail and entry step to the Stock Jeep JK Rubicon rocker rails, Poison Spyder Rocker Knockers or other aftermarket plate steel rocker armor.
The components provided in the kit are similar to Poison Spyder Ricochet Rockers, hence the name of the kit.
The kit includes:- DOM tube rub rails
- Rico Steps and end gussets
The DOM tube pieces are CNC bent and pre-Notched, ready to weld on. The Rico Steps and gussets are laser cut from plate steel. The steps are brake-formed to provide extra strength and reverse-dimpled for foot traction.
The main tubes measure 45.25 inches long and the kit was designed specifically for the TJ, YJ and CJ-7, but might possibly be used on other vehicles if it fits. Requires welding.SKU: DIY-50-020-PSC -
Rock Sliders
DIY Rico Step Kit 54.5 Poison Spyder – DIY-50-040
DIY Rico Step Kit 54.5 inch.The DIY Rico Step Kit from Poison Spyder allows the do-it-yourselfer to add a heavy duty rub rail and entry step to the Stock Jeep JK Rubicon rocker rails, Poison Spyder Rocker Knockers or other aftermarket plate steel rocker armor.
The components provided in the kit are similar to Poison Spyder Ricochet Rockers, hence the name of the kit.
The kit includes:- DOM tube rub rails
- Rico Steps and end gussets
The DOM tube pieces are CNC bent and pre-Notched, ready to weld on.
The Rico Steps and gussets are laser cut from plate steel. The steps are brake-formed to provide extra strength and reverse-dimpled for foot traction.
The main tubes measure 54.5 inches long and the kit was designed specifically for the JK 2-door, LJ, and CJ-8, but might possibly be used on other vehicles if it fits. Requires welding.SKU: DIY-50-040-PSC -
Rock Sliders
DIY Rico Step Kit 66.5 (JK 4-Dr) Poison Spyder – DIY-50-050
DIY Rico Step Kit 66.5 inch. (JK 4-Dr) The DIY Rico Step Kit from Poison Spyder allows the do-it-yourselfer to add a heavy duty rub rail and entry step to the Stock Jeep JK Rubicon rocker rails or other aftermarket plate steel rocker armor.
The components provided in the kit are similar to Poison Spyder Ricochet Rockers, hence the name of the kit.
The kit includes:- DOM tube rub rails
- Rico Steps and end gussets
The DOM tube pieces are CNC bent and pre-Notched, ready to weld on. The Rico Steps and gussets are laser cut from plate steel. The steps are brake-formed to provide extra strength and reverse-dimpled for foot traction. The main tubes in this kit measure 66.5 inches long and includes front and rear step plates, as it was designed specifically for the JK Unlimited (4-door), but might possibly be used on other vehicles if it fits. Requires welding.
SKU: DIY-50-050-PSC -
Rock Sliders
DIY Slider Tube Kit 39.5 Poison Spyder – DIY-08-010
DIY Slider Tube Kit 39.5 inches. The DIY Slider Tube Kit from Poison Spyder allows the do-it-yourselfer to add a rugged DOM tube slider to Poison Spyder Rocker Knockers or other aftermarket plate steel rocker armor.
The kit includes:- The slider tubes as well as the short tube supports to brace the center of the tube against the rocker, to do both sides of the Jeep
The DOM slider tube pieces are CNC bent and pre-Notched to mount at an angle, as with our ready-built Rocker Knockers with Sliders.
The main tubes measure 39.5 inches long and the kit was designed specifically for the Jeep CJ-5, but might possibly be used on other vehicles if it fits. Requires welding.SKU: DIY-08-010-PSC -
Rock Sliders
DIY Slider Tube Kit 44.25 Poison Spyder – DIY-08-020
DIY Slider Tube Kit 44.25 inch. The DIY Slider Tube Kit from Poison Spyder allows the do-it-yourselfer to add a rugged DOM tube slider to Poison Spyder Rocker Knockers or other aftermarket plate steel rocker armor.
The kit includes:- The slider tubes as well as the short tube supports to brace the center of the tube against the rocker, to do both sides of the Jeep.
The DOM slider tube pieces are CNC bent and pre-Notched to mount at an angle, as with our ready-built Rocker Knockers with Sliders.
The main tubes measure 44.25 inches long and the kit was designed specifically for the Jeep TJ, YJ and CJ-7, but might possibly be used on other vehicles if it fits. Requires welding.SKU: DIY-08-020-PSC -
Rock Sliders
DIY Slider Tube Kit 53.75 Poison Spyder – DIY-08-030
DIY Slider Tube Kit 53.75 inch. The DIY Slider Tube Kit from Poison Spyder allows the do-it-yourselfer to add a rugged DOM tube slider to Poison Spyder Rocker Knockers or other aftermarket plate steel rocker armor.
The kit includes:- The slider tubes as well as the short tube supports to brace the center of the tube against the rocker, to do both sides of the Jeep
The DOM slider tube pieces are CNC bent and pre-Notched to mount at an angle, as with our ready-built Rocker Knockers with Sliders.
The main tubes measure 53.75 inches long and the kit was designed specifically for the Jeep LJ and CJ-8, but might possibly be used on other vehicles if it fits. Requires welding.SKU: DIY-08-030-PSC -
Fire Extinguisher Mount
Fire Extinguisher Holder Poison Spyder – 57-62-110
The Poison Spyder Fire Extinguisher Holder easily mounts to any roll cage tube or other suitable location, and securely holds a Standard 2.5 lb. automotive fire extinguisher (up to 12 inches long). Made of high quality nylon webbing with an rubberized Poison Spyder emblem.
Note: The Velcro straps that hold this unit to the roll bar are optimally sized for use on padded roll bars. When using on bare, un-padded tubes (1.75 inch OD or larger recommended), the ends of the Velcro straps will be too long, but can either be tucked in or cut off (use a lighter to cauterize the cut edge of the nylon webbing).SKU: 57-62-110-PSC -
Flashlight Holder
Flashlight Holder 2 Cell Poison Spyder – 57-62-010
Poison Spyder Flashlight Holder 2-Cell. The Poison Spyder Flashlight Holder easily mounts to any roll cage tube or other suitable location, and securely holds a Standard 3-Cell Flashlight.
Velcro flap keeps the flashlight in place but quickly accessible. Made of high quality nylon webbing with an embroidered Poison Spyder tag.SKU: 57-62-010-PSC -
Flashlight Holder
Flashlight Holder 3-Cell Poison Spyder – 57-62-011
Poison Spyder Flashlight Holder 3-Cell. The Poison Spyder Flashlight Holder easily mounts to any roll cage tube or other suitable location, and securely holds a Standard 3-Cell Flashlight.
Velcro flap keeps the flashlight in place but quickly accessible. Made of high quality nylon webbing with an embroidered Poison Spyder tag.SKU: 57-62-011-PSC
