4-Pin LED Flasher 97-00 TJ Poison Spyder – 41-04-026
4-Pin LED Flasher 1997-2000 TJ. Electronic flasher to provide proper current intermittent for LED taillights and turn signals in your Jeep 1997-2000 Jeep TJ. Easy to install (instructions included).
4 24-LED Taillight Push-In with Pigtail & Grommet Red Poison Spyder – 41-04-0500 out of 5(0)
4 24-LED Taillight Push-In with Pigtail and Grommet Red. These 24-diode LED taillights easily install using a rubber grommet they simply push into place. This is a 4 inch round light (requires a 4.5 inch hole) with red lens.
Flush-mount LED taillights stay out of the way of rocks and trees on the trail, last longer and shine brighter than OEM incandescent lamps. Available with red or clear lens (make your selection in the options) units with clear lenses use red diodes, so they still flash red when lit up.
These install right into Poison Spyder Customs Crusher Corners or Trail Corners (on units specifically ordered for LED taillights), or can be installed into other manufacturer corner protectors or anywhere you can cut a 4.5 inch round hole in a flat panel.
Includes the LED lamp assembly, rubber grommet and wiring pigtail harness. Sold each (order 2 if you need a pair).SKU: 41-04-050-PSC
Side Marker Lights
Rectangular LED Marker Lamp Amber Poison Spyder – 41-04-2030 out of 5(0)
Rectangular LED Marker Lamp Amber. This rectangular LED Marker Lamp is the solution for those who need to run a combination marker lamp and turn signal in the same unit. This may be necessary on Jeeps where the OE turn signals and/or marker lamps were removed in order to install aftermarket armored fenders such as Poison Spyder DeFenders. Unlike our 3/4 inch Round LED Marker Lamp, these are a 3-wire lamp which can perform two separate functions (minor and majoror typically, marker lamp and turn signal)
For those needing a combination marker lamp/turn signal to satisfy local legal requirements, the small rectangular shape makes this lamp the ideal size to mount along the outer edge of the Poison Spyder DeFender.
Installation requires simply drilling a 3/8 inch hole, thoroughly cleaning the mounting surface, peeling back the adhesive cover, pushing the wires through the hole then firmly pressing to set the adhesive, then making the wiring connections.
Note that this is a surface-mount lamp. If mounting on the outer edge of the Poison Spyder DeFenders, it may serve to satisfy local DMV/DOT requirements, however it will be mounted in a vulnerable spot if your Jeep is wheeled hard in tight situations. DeFenders are designed as trail armor, and are intended to be rubbed along the rocks, trees, etc., which would of course damage this lamp if mounted along the outer surface. The lamp may be mounted in more protected areas by either drilling a hole or fabricating a simple mounting bracket, at the installers discretion.
Features and Benefits
Lamps operate in minor and major output levels; major function activated by the brake function or turn signal
Major function is 3 times brighter than minor function (amber)
Red Major function is 7 times brighter than minor function
Provides marker/clearance solution that requires no mounting brackets or installation screws
Lamps adhere directly to application surface through use of heavy-duty adhesive backing
Electronics are completely sealed in epoxy to resist damage caused by moisture and corrosion
Easy-to-install peel-off liner
Rear exit wire version requires a 3/8 inch mounting hole, and self-seals hole upon installation
- Polycarbonate Lens
- Over-Molded Housing
- Encapsulated Circuitry
- 20 Gauge Wire
- 3 Light Emitting Diodes (LED)
- Designed at 13.5v
- (Minor)0.004A – 0.015A
- (Major)0.048A – 0.068A
Side Marker Lights
3/4 LED Marker Lamp 3-Wire Clear/Amber Poison Spyder – 41-04-0800 out of 5(0)
3/4 LED Marker Lamp 3-Wire Clear/Amber. 3/4 inch round, Amber lens LED lamp for use as a combination turn signal and running lamp, for use with Poison Spyder Customs DeFenders, Tube Fenders, Crusher Flares, or anywhere you’d like to mount them by drilling a 3/4 inch hole in a flat panel.
This is a 3-WIRE assembly, meaning it can be used as both a turn signal AND a marker lamp simultaneously. It can also be used as only a marker lamp (or only a turn signal) by using two wires and leaving the third wire unused. These high quality LED lamps are DOT-approved for use on your vehicle. Includes pigtail harness and mounting grommet. Sold each (select a quantity of 2 if you need a pair).
This item is also available in red or clear/amber.
Important: This item is Not intended as a direct replacement for any Stock turn signal or marker lamp. It does Not plug directly into the vehicle wiring harness it will require cutting and splicing into the vehicle wiring harness.
- 3/4 high intensity LED
- 3-wire design to function as turn signal, marker lamp, or both
- Clear lens with Amber diode
- Install in any flat panel with a 3/4 hole
- Requires cutting and splicing into vehicle’s wiring harness
2-1/2 LED Back-Up Light Clear Poison Spyder – 41-04-3000 out of 5(0)
2.5 Inch LED Back-Up Light Clear. 2.5 inch flush mount LED back-up light for use with Poison Spyder Customs Crusher Corners, Trail Corners or any other manufacturer corner protectors, or anywhere you can cut a 2.75 inch hole in a flat sheetmetal panel. push-in mounting with the included rubber grommet. Sold by each, if you need a pair specify a quantity of 2.SKU: 41-04-300-PSC$28.99
4 6-LED Taillight Flange Style Poison Spyder – 41-04-0360 out of 5(0)
4 6-LED Taillight Flange Style. 6-diode flush mount LED taillight with red lens for use with Poison Spyder Customs Crusher Corners, Trail Corners or any other manufacturer corner protectors, or anywhere you can cut a 4.5 inch hole in a flat sheet metal panel. Flange-mounting style, red lens.
Sold by each, if you need a pair specify a quantity of 2.SKU: 41-04-036-PSC$35.99