|Dimensions||1 × 1 × 1 in|
3-Way Spare Tire Strap Poison Spyder – 57-63-001
The Poison Spyder 3-Way Spare Tire Strap securely holds the spare tire in place during the Most rigorous four-wheeling. This strap was designed for use with the Poison Spyder Rear Stinger Tire Carrier, but can be used with other DIY-fabricated spare tire mounts or to simply tie the spare tire down into the bed of the vehicle.
The use of a strap allows virtually infinite adjustability for any size tire, while allowing quick, easy access to the spare tire without having to use any extra tools. All of these reasons are why similar straps are routinely used for spare tire hold-down duty in off-road racing.
Heavy duty ratchet lets you easily adjust, tighten and release tension. Made of high quality nylon webbing with an embroidered Poison Spyder tag.
Slant Mount for XRC Tire Carrier Jeep JK Black Powdercoat Smittybilt – 76857-050 out of 5(0)
Spare tire carriers in their conventional, upright positions are a necessity for every Jeeper, whether on the road or off, but when the terrain gets extreme and your standard hard top comes off, Smittybilt’s new Slant Back Tire Carrier Kit allows you to move your spare tire into an aggressive, 45 degree pre-runner position.
- Slant Tire Carrier Adapter Kit
- Designed for use with Smittybilt’s XRC Gen2 Bolt-On Tire Carrier (P/N 76857), Cargo Restraint System (C.RES), or JK Bowless Tops
- Manufactured from 3/16 inch cold rolled steel, weighs 8 lbs
- 1 inch diameter hardened pin
- Easy, bolt-on installation
- All hardware included
- Compatible with Rotopax gas/water can and off-road jack mounts, if used with XRC Gen2 Bolt-on Tire Carrier (P/N 76857)
- Matte Black Powdercoat Finish
- 5-Year Limited Warranty On Powdercoat
- Lifetime Limited Warranty On Structure
- Sold As A Kit
- Combination of Pivot Tire Carrier (P/N 2843) and Slant Adapter (P/N 76857-05) is not compatible with Smittybilt Slant Hard Top (P/N 518702 or P/N 517702)
- 2007-2018 Jeep JK Wrangler
- 2007-2018 Jeep JK Wrangler Unlimited
SRC Oversize Tire Carrier 07-18 Wrangler JK Smittybilt – 27430 out of 5(0)
The Smittybilt Oversize Tire Mount is the most economical way to mount an over sized tire onto your 2007-2016 JK Wrangler. Attaches to the factory tailgate using the existing holes and requires no drilling or modifications. Completely adjustable and designed to mount up to a 37 Inch tire or up to 195 lbs. Engineered to integrated with existing tailgate and works as one solid unit. Carrier and tailgate open and close as a single unit. Adjustable arm eliminates tailgate sag. Comes in a signature series matte black textured finish.
- Fits 2007 to 2016 Wrangler, Rubicon and Unlimited
- 2 and 4-door models
- Textured black finish
- Attaches to the factory tailgate
- Holds up to a 37 Inch tire
- Adjustable arm eliminates tailgate sag
- Designed to use a pad lock for security
- Does not work with factory wheels
DV8 Offroad TCJL-02 Jeep JL Body Mounted Tire Carrier0 out of 5(0)
TCJL-02 2018+ Jeep JL Body Mounted Tire Carrier
The DV8 Offroad TCJL-01 uses a combination of tubing, boxed steel and internal bracing to accommodate up to a 42 tire and wheel combo and can be used with any rear bumper. DV8 used a spring loaded pin system to make opening and closing the tire carrier so easy that it can be done with one hand full. The tire carrier accommodates the OEM back-up camera and comes with a new third brake light. Install is extremely simple with minimal drilling and provided tailgate hinges.
-Accommodates up to a 42 tire
-Fits any bolt pattern wheel
-Rigid mounting system
-DV8 textured powdercoatSKU: TCJL-02
JK HD Aluminum Hinged Carrier Kit 07-Pres Wrangler JK TeraFlex0 out of 5(0)
JK BFH II Rear Crossmember Poison Spyder – 17-17-0100 out of 5(0)
JK BFH II Rear Crossmember for Jeep Wrangler JK 2007-2016. By itself or used in conjunction with the JK BFH II Rear Bumper, this Built For the Hammers crossmember strengthens the Jeep JK Wrangler rear frame when trimmed for maximum ground clearance and departure angle.
- Heavy Duty replacement for Stock crossmember
- Works with BFH II Rear Bumpers
- May by used by itself for minimalist bumper
- CNC laser cut brake-formed 3/16 steel plate
Plate Steel Construction
The BFH II Rear Crossmember is CNC laser-cut from high strength 3/16 inch plate steel, then precision brake-formed for an exact fit. Dimpled lighting holes remove unnecessary weight while creating a custom look for those who choose to run the crossmember by itself without a rear bumper to cover it.
High Clearance and Departure Angle
The minimalist design of the JK BFH II Rear Bumper provides the Most ground/obstacle clearance and best departure angle possible while preserving the integrity of the Jeep JK frame strength. Installation requires trimming the bulky rear frame rails and Stock bumper mounts and welding in the new crossmember. A laser-cut steel template is provided to assist with making the right cuts.
Use By Itself or With BFH II Rear Bumper
The BFH II Rear Crossmember may be used by itself as an ultra-minimalist, high clearance rear bumper. But it is designed to be used with the Poison Spyder BFH II Rear Bumper. The bumper fits over the crossmember like a glove. Together, this combination provides the frame-strengthening characteristics of the crossmember along with the aesthetics of the BFH II Rear Bumper. This specific part number for the crossmember does Not include an integrated hitch receiver, so it can only be used with the K BFH II Rear Bumper – Tabs or K BFH II Rear Bumper – Tabs – Lights. A different version of the BFH II Crossmember is available with a hitch receiver (p/n 17-17-030)
NotES: Installation requires cutting of Stock frame rails and welding! Please read through the Installation Instructions so that you are Fully aware of the modifications required to your Jeep frame rails, before purchasing.
This product ships as bare steel it will need to be painted after installation.SKU: 17-17-010-PSC$249.99