Category: Front Bumpers
Tags: Bumpers, Bumpers & Armor, Exterior Parts & Car Care, Front Bumpers
Brand: Smittybilt
Front Bumpers
Tubular Bumper Front 07-18 Wrangler JK W/ Hoop Gloss Black Smittybilt – JB48-F
Smittybilt Tubular Jeep Bumpers are custom crafted to fit your Jeep. They gain their strength from durable stainless steel and a 1-piece design, plus boast pre-cut vertical uprights for a little flair. And, these bumpers are robotically welded for extreme durability on the road or off. Plus, Smittybilt Tubular Jeep Bumpers are available for the front and rear. The rear bumper even includes an added tow hitch receiver with a 2000 lb towing weight. Choose your Jeep bumpers with a polished or triple chrome-plated finish.
Details:
- Fits 2007 to 2018 Jeep JK Wrangler, Rubicon and Unlimited
- 2 and 4-door models
- Front Bumper
- With Hoop
- Gloss Black
- No Drill Installation
- 5-year limited warranty
$209.99
Related products
-
Front Bumpers
SRC Classic Front Bumper 07-18 Wrangler JK Black Textured Smittybilt – 76741
When you need the toughest, most durable bumper system out there, look to the Smittybilt Rock Crawler Series! These heavy duty bumpers are designed for off road use and abuse! Durable powder coat painted 2 tubes and 1/4 steel plate protects your front end from large rocks. Each bumper has been designed with sloping ends for greater tire travel and enhanced entry and exit.
Details:- Fits 07-2018 Wrangler JK
- Zinc Undercoated dual stage black textured power coat
- Four taps to mount lights
- Wide opening allows for winch installation
- 1/4 Inch thick custom mounting brackets
- Welded d-ring tabs
- Durable 2 Inchx.120 Inch wall over built
- Bumpers bolt directly to your vehicle
- Requires no drilling or modifications
- 5-year limited warranty
SKU: n/a -
Front Bumpers
SRC Classic Front Bumper W/Winch Plate 07-18 Wrangler JK Black Textured Smittybilt – 76743
Front BumpersSRC Classic Front Bumper W/Winch Plate 07-18 Wrangler JK Black Textured Smittybilt – 76743
Manufactured from 3/16 Inch cold rolled steel plate and will provide you the maximum protection. Available with D-rings tabs and the new Wrangler bumper is offered with a winch mount that holds up to a 10,000 lb. winch. Bumpers bolt directly to your vehicle and require minor drilling to finish installation. Two stage matte black powder coat finish with 5-year limited warranty. D-rings are not included.
Details:- Fits 2007 to 2018 Jeep JK Wrangler, Rubicon and Unlimited
- 2 and 4-door models
- Two stage matte Black powder coat finish
- Manufactured from 3/16 Foot‹ cold rolled steel plate
- Bumpers bolt directly to your vehicle
- 5-year limited warranty
SKU: n/a -
Front Bumpers
JK Brawler MID Front Bumper Brawler Bar Tabs Black Poison Spyder – 17-63-010-DBTP1
JK Brawler Mid Front Bumper Brawler Bar Tabs Black for Jeep Wrangler JK 2007-2016. The Brawler Mid front bumper for JK is a Mid-width, high clearance bumper designed to combine off-road performance with Full features. This bumper is fabricated from 3/16 inch plate steel, CNC laser-cut and precision brake-formed into a low profile, high clearance design.
The ends of the bumper extend farther outboard than our Brawler Lite bumper, to about half the width of the tires. This provides increased brush protection for the grille corners and fenders, and gives the Jeep a more expeditionary look than our more rock-crawling specific bumpers. This product ships as bare steel it will need to be painted or powdercoated prior to final installation. We do Not offer a powdercoat option for this item.
Features:- SpyderShell Armor Coat finish with 5-Year Warranty
- Mid-width, multi-faceted design protects lower grille and extends halfway across the front of the tires
- CNC laser cut from 3/16 plate steel, precision brake-formed for a perfect fit
- Recessed light buckets accept OE fog lamps or Rigid Industries Duallys by use of adapter plate (sold separately)
- Brawler Bar made of 1.5 X .120 wall DOM tubing with 1.25 OD X .120 wall DOM tube gussets
This bumper is fabricated from 3/16 inch plate steel, CNC laser-cut and precision brake-formed into a low profile, high clearance design. The ends of the bumper extend far enough to protect the lower corner of the JK grille, but Not far enough to hinder tire clearance or tire access to vertical obstacles.
Brawler Bar
(This part number is for the Brawler Mid without any Brawler Bar. Click Here for the Brawler Mid with Brawler Bar). The Brawler Bar is modeled after the bar found on our original RockBrawler front bumper. It is a low-profile stinger designed to provide protection to the winch, grille and radiator area. The Brawler Bar is made of CNC laser-Notched, NC-bent 1 3/4 inch diameter .120 inch wall DOM tubing. The complex laser-cut Notch allows the Brawler Bar to be welded to two different planes on the surface of the bumper, providing incredible strength. Two gusset styles are offered for strengthening the Brawler Bar. CNC laser-cut brake-formed 3/16 inch plate steel or CNC laser Notched DOM tubing.Note: Warn PowerPlant winches are Not a direct-fit with the DOM Tube gussets (they may be installed with some minor modifications by the installer).
Easy Installation
Unlike the Poison Spyder BFH series bumpers for JK, the Brawler Mid can be mounted without cutting or altering the Jeep frame rails. The faceted design of the Brawler Mid provides the best ground clearance and approach angle possible in a bumper that does not require frame modifications. The factory Crash Bar may be left intact or removed for a sleek appearance and high clearance. If keeping the crash bar, we recommend adding the Brawler Mid Skid Plate (sold separately), which conceals the crash bar and protects the electronic sway bar disconnect.
Recessed Fog Lamp Mounts
Brawler Mid comes with provisions for re-mounting your factory fog lamps. These consist of recessed fog lamp buckets that are made of CNC laser cut DOM tubing with a mounting flange designed to accept the mounting hardware of the Stock lamps. The recess and all-steel buckets help protect the lamps from the rocks. For those who do Not have the Stock fog lamps, or would like to upgrade to more powerful LED lamps, Poison Spyder offers a unique LED Fog Lamp Mounting Kit for installing a pair of Rigid Industries Dually LED lamps in the fog lamp locations.
Important: The Stock fog lamps used on the Jeep Wrangler 10th Anniversary Rubicon do Not fit into the fog lamp buckets on this bumper. If installing this bumper on a 10th Anniversary Rubicon, we suggest using a pair of Rigid Industries Dually or Dually D2 LED lamps along with our JK Dually Fog Lamp Mounts instead of the Stock fog lamps.
Winch Compatibility
The Brawler Mid bumper is designed to accept Most Warn winches, and winches from other manufacturers that conform to Warn Standardized winch mounting dimensions. The winch sits in a slight depression on the top surface of the bumper, with plenty of CNC laser cut plate steel gusseting inside the bumper shell, directly underneath the winch to provide maximum strength.The Winch Fairlead Mount is sold separately, so that those who wish to Not run a winch are left with a clean looking, unobstructed top surface on their bumper. Important: installing the Warn Zeon winch on the Brawler Mid Front Bumper requires Two sets of our Zeon Winch Spacer Plates (p/n 45-57-010-03, sold separately).
Recovery Shackle Tabs
Optional Recovery Shackle Tabs are modeled after the high clearance tabs designed for our hard core BFH series bumpers. These tabs are angle to provide maximum approach angle. They are CNC machined from 1 inch thick steel billet, specifically designed to accept our heavy duty 3/4 inch Recovery Shackles. Selecting this option will get you a pair of these tabs, expertly welded to the Brawler Mid bumper.
Optional Brawler Mid Skid
The optional Brawler Mid Skid attaches to the bottom of the Brawler Mid bumper to conceal and protect the Stock crash bar, plus it has an extension to protect the electronic swaybar disconnect motor found on Rubicon JKs.The skid is made of CNC laser-cut 3/16 inch plate steel, precision brake-formed for a precise fit to the Brawler Mid front bumper.
A separate version of the Brawler Mid is available without the Brawler Bar. The Brawler Mid comes to you as bare steel, ready to accept paint or powdercoat in the color of your choice. A powdercoat option for this item is Not currently available directly through Poison Spyder.SKU: 17-63-010-DBTP1-PSC -
Front Bumpers
JK Brawler FULL Width Front Bumper Tabs Poison Spyder – 17-64-020-D
JK Brawler Full Width Front Bumper Tabs for Jeep Wrangler JK 2007-2016. The Brawler Full Width Front Bumper for JK provides the highest ground and tire clearance possible in a Full width JK bumper. This bumper brings Poison Spyder form and function to the overlander market, and to those who would like to keep their Stock JK fender flares.
The bumper extends to the Full width of the Stock flares, to integrate with them cleanly while protecting them from trail hazards. This configuration includes recessed fog light buckets and high clearance recovery shackle tabs. Like all bumpers in the Brawler product line, the Full Width is fabricated from 3/16 inch plate steel, CNC laser-cut and precision brake-formed into a low profile, high clearance design. This product ships as bare steel. It will need to be painted or powdercoated prior to final installation. We do Not yet offer a powdercoat option for this item.
Features:- Full-width, multi-faceted design protects lower grille and extends to outer edge of Stock flares
- CNC laser cut from 3/16 plate steel, precision brake-formed for a perfect fit
- Recessed light buckets accept OE fog lamps or Rigid Industries Duallys by use of adapter plate (sold separately)
- Brawler Bar made of 1.5 X .120 wall DOM tubing with 1.25 OD X .120 wall DOM tube gussets
- High clearance recovery shackle tabs
- CNC machined from 1 thick plate steel
Full Width
Finally there is a Full Width front bumper that incorporates Poison Spyders attention to form and function, in an elegant package that integrates perfectly with the Stock Jeep or aftermarket Stock replacement fender flares. While this bumper was designed for those Jeep enthusiasts who prefer a more overland style and function to their Jeep build, or want to keep their factory flares, we could not simply make a Full-width monstrosity like so many unsightly bumpers already on the market. Even though it is Full width, and less likely to be used on the hard core rock trails, we still felt compelled to design it with maximum approach angle, ground clearance and tire clearance possible while still extending out to the Full width of the Stock flares to protect the corners of the Jeep.The lower skid plate is sold separately, so that those who would rather run without it (and gain even more ground clearance) may do so. The outriggers that extend to the edge of the flare are kept as tight to the original Brawler high clearance lines as possible, tapering outward toward the ends. This allows the tires the best access to grab obstacles to pull the Jeep up and over rather than impeding progress when metal meets rock. The outriggers are designed to integrate visually with the Stock fender flares, in a clean, almost factory look. The back side of the outrigger is scalloped to provide maximum clearance for up to a 37 inch tire with minimal suspension lift.
Plate Steel Construction
Every Brawler bumper starts out as a sheet of 3/16 inch plate steel. Our CNC laser cutter precisely cuts the flat pattern as designed in our 3D CAD system. Next the bumper parts are CNC brake-formed into the high clearance, multi-faceted pieces that will become a finished bumper. Highly skilled tradesmen weld each bumper together using precision-engineered assembly fixtures for a perfect fit. Finally the complete bumper is sent through our finishing department for final appearance surfacing and quality control checks.
Easy Installation
Poison Spyder Brawler series front bumpers can be mounted without cutting or altering the Jeep frame rails. The faceted design of the Brawler Full Width Front Bumper provides the best ground clearance and approach angle possible in a Full width bumper that doesn’t require frame modifications. The factory Crash Bar may be left intact or removed for a sleek appearance and high clearance. If keeping the crash bar, we recommend adding the Brawler Lite Skid Plate (p/n 17-59-030, sold separately), which conceals the crash bar and protects the electronic sway bar disconnect.
Recessed Fog Lamp Mounts
Every Brawler Front Bumper comes with provisions for re-mounting your factory fog lamps. These consist of recessed fog lamp buckets that are made of CNC laser cut DUM tubing with a mounting flange designed to accept the mounting hardware of the Stock lamps. The recess and all-steel buckets help protect the lamps from the rocks. For those who do Not have the Stock fog lamps, or would like to upgrade to more powerful LED lamps, Poison Spyder offers a unique LED Fog Lamp Mounting Kit (p/n RIG-DLYFOGMNT) for installing a pair of Rigid Industries Dually LED lamps in the fog lamp locations.
Important: The Stock fog lamps used on the Jeep Wrangler 10th Anniversary Rubicon do Not fit into the fog lamp buckets on this bumper. If installing this bumper on a 10th Anniversary Rubicon, we suggest using a pair of Rigid Industries Dually or Dually D2 LED lamps along with our JK Dually Fog Lamp Mounts instead of the Stock fog lamps.
Winch Compatibility
The Brawler Full Width Front Bumper is designed to accept Most Warn winches, and winches from other manufacturers that conform to Warn Standardized winch mounting dimensions. The winch sits in a slight depression on the top surface of the bumper, with plenty of CNC laser cut plate steel gusseting inside the bumper shell, directly underneath the winch to provide maximum strength. The Winch Fairlead Mount (p/n 45-57-010) is sold separately, so that those who wish to Not run a winch are left with a clean looking, unobstructed top surface on their bumper. Important: installing the Warn Zeon winch on the Brawler Mid Front Bumper requires a set of our Zeon Winch Spacer Plates (p/n 45-57-010-03).
Recovery Shackle Tabs
Recovery Shackle Tabs are Standard equipment on the Brawler Full Width Front Bumper. These 3D CAD designed tabs are modeled after the high clearance tabs designed for our hard core BFH series bumpers, providing maximum approach angle while minimizing hang-ups on rock obstacles. They are CNC machined from 1 inch thick steel billet, specifically designed to accept our heavy duty 3/4 inch Recovery Shackles.
Optional Brawler Lite Skid
The optional Brawler Lite Skid Plate (p/n 17-59-030) attaches to the bottom of the Brawler Full Width Front Bumper to conceal and protect the Stock crash bar, plus it has an extension to protect the electronic swaybar disconnect motor found on Rubicon JKs.The skid is made of CNC laser-cut 3/16 inch plate steel, precision brake-formed for a precise fit to the Brawler Full Width Front Bumper (yes, the Brawler Lite and Brawler Full Width share the same skid plate).
A separate version of the Brawler Full Width Front Bumper is available with the DOM tubular Brawler Bar.The Brawler Full Width Front Bumper comes to you as bare steel, ready to accept paint or powdercoat in the color of your choice. A powdercoat option for this item is Not currently available directly through Poison Spyder. See your nearest Poison Spyder dealer for powdercoating options through a coating shop near you.
SKU: 17-64-020-D-PSC -
Front Bumpers
JK Brawler Lite Front Bumper Brawler Bar Tube Gussets Tabs Poison Spyder – 17-59-010-DBT
Front BumpersJK Brawler Lite Front Bumper Brawler Bar Tube Gussets Tabs Poison Spyder – 17-59-010-DBT
JK Brawler Lite Front Bumper Brawler Bar Tube Gussets Tabs for Jeep Wrangler JK 2007-2016. The Brawler Lite front bumper for JK is a grille-width, high clearance bumper designed to combine hard core off-road performance with Full features.
This bumper is fabricated from 3/16 inch plate steel, CNC laser-cut and precision brake-formed into a low profile, high clearance design. The ends of the bumper extend far enough to protect the lower corner of the JK grille, but Not far enough to hinder tire clearance or tire access to vertical obstacles. This product ships as bare steel it will need to be painted or powdercoated prior to final installation. We do Not offer a powdercoat option for this item.
Features:- Compact, multi-faceted design protects lower grille corners while giving tires plenty of clearance and access to climb obstacles
- CNC laser cut from 3/16 plate steel, precision brake-formed for a perfect fit
- Recessed light buckets accept OE fog lamps or Rigid Industries Duallys by use of adapter plate (sold separately)
- Brawler Bar made of 1.5 X .120 wall DOM tubing with 1.25 OD X .120 wall DOM tube gussets
- High clearance recovery shackle tabs
- CNC machined from 1 thick plate steel
Plate Steel Construction
This bumper is fabricated from 3/16 inch plate steel, CNC laser-cut and precision brake-formed into a low profile, high clearance design. The ends of the bumper extend far enough to protect the lower corner of the JK grille, but Not far enough to hinder tire clearance or tire access to vertical obstacles.
Brawler Bar
The Brawler Bar is modeled after the bar found on our original RockBrawler front bumper. It is a low-profile stinger designed to provide protection to the winch, grille and radiator area. The Brawler Bar is made of CNC laser-Notched, NC-bent 1.75 inch diameter .120 inch wall DOM tubing. The complex laser-cut Notch allows the Brawler Bar to be welded to two different planes on the surface of the bumper, providing incredible strength. Two gusset styles are offered for strengthening the Brawler Bar. CNC laser-cut brake-formed 3/16 inch plate steel or CNC laser Notched DOM tubing. Note: Warn PowerPlant winches are Not a direct-fit with the DOM Tube gussets (they may be installed with some minor modifications by the installer).
Easy Installation
Unlike the Poison Spyder BFH series bumpers for JK, the Brawler Lite can be mounted without cutting or altering the Jeep frame rails. The faceted design of the Brawler Lite provides the best ground clearance and approach angle possible in a bumper that does Not require frame modifications. The factory Crash Bar may be left intact or removed for a sleek appearance and high clearance. If keeping the crash bar, we recommend adding the Brawler Lite Skid Plate (sold separately), which conceals the crash bar and protects the electronic sway bar disconnect.
Recessed Fog Lamp Mounts
Brawler Lite comes with built-in, recessed fog lamp mounts that are designed to easily accept your Stock fog lamps. And these are Not just simple light tabs placed behind a hole in the bumper they are recessed in a bucket made of a Full tubular section to encircle the lamp and keep light from annoyingly leaking behind and around the bumper.Adding further convenience are mounting holes for re-installing the harness retainer clips for the factory wiring, to keep the wiring neatly secured. If you would like a lot more power than the factory fog lamps provide, you can opt to install a set of Rigid Industries Dually or D2 Dually LED lamps using our JK Fog Light Mounts for Rigid Industries Dually/D2.
Important: The Stock fog lamps used on the Jeep Wrangler 10th Anniversary Rubicon do Not fit into the fog lamp buckets on this bumper. If installing this bumper on a 10th Anniversary Rubicon, we suggest using a pair of Rigid Industries Dually or Dually D2 LED lamps along with our JK Dually Fog Lamp Mounts instead of the Stock fog lamps.
Winch Compatibility
The Brawler Lite top-mounted, integrated winch mount is part of the Fully boxed, internally gusseted bumper shell. Winches that are mounted inside the bumper lose this box strength as well as the strength of internal gussets.The Brawler Lite is designed to accept Most Warn and other brand winches that use the popular 10 inch X 4.5 inch mounting pattern, with a few small exceptions. Warn Powerplant winches fit the Brawler Lite with Brawler Bar and Plate Gussets just fine, however it will require slight modifications to use this winch with the Tube Gusset variant. Mounting the Warn Zeon winches requires our Zeon Winch Spacer Plates. See the FAQ section below for further information on both of these winches.
Recovery Shackle Tabs
Optional Recovery Shackle Tabs are modeled after the high clearance tabs designed for our hard core BFH series bumpers. These tabs are angle to provide maximum approach angle. They are CNC machined from 1 inch thick steel billet, specifically designed to accept our heavy duty 3/4 inch Recovery Shackles. Selecting this option will get you a pair of these tabs, expertly welded to the Brawler Lite bumper.Separate versions of the Brawler Lite are available without the Brawler Bar or with the Trail Stinger. The Brawler Lite comes to you as bare steel, ready to accept paint or powdercoat in the color of your choice. A powdercoat option for this item is Not currently available directly through Poison Spyder.
SKU: 17-59-010-DBT-PSC
