Drive Shaft
Rubicon Express Drive Shaft Package for 12-17 JK Wrangler Unlimited and Rubicon Unlimited (Auto Trans) – JK1801
Prevent driveline vibration after you lift your Jeep JK with our Dana Spicer 1310 CV style JK driveshafts. Designed to replace the factory shafts and to be ran with our replacement yoke and flange for the transfer case. Built for daily driving and the demands of off roading. Driveshaft lengths are for factory gasoline motors.
Technical Details
- Fits 2012 to 2018 JK Wrangler Unlimited and Rubicon Unlimited
- 4-door models
- Automatic transmission
- Includes front and rear drive shafts and yoke flanges
- 1310 U-joints
- Dynamically balanced to eliminate vibration
- Available from 15.5 to 38.5 inches long
- Recommended in vehicles with 3.5 inches or more of lift
- Billet aluminum flange
$988.99
Related products
-
Drive Shaft
NP231 Tail Shaft Conversion Kit Pro Comp Suspension
The Tail Shaft Conversion kit for 5 Front/Rear lift height shortens the Transfer Case allowing for a 4 Inch longer CV Style drive shaft, improves driveline alignment, reduces bind, friction and vibration. drive shaft sold separately. Fits NP231 Transfer Case Only. Will not fit NP207 in some models.
Details:- Fits 1987 to 2006 Wrangler and Unlimited
- For NP231 transfer case only
- 20 percent Larger mainshaft over factory shaft
- 4 Inch shorter than stock
SKU: 4007-PRO -
Drive Shaft
Rubicon Express CVF Drive Shat Rear 15.5 Inch Flange Style Slip Yoke Elminator Only W/PN RE1801/RE1807 – RE1898-155
Drive ShaftRubicon Express CVF Drive Shat Rear 15.5 Inch Flange Style Slip Yoke Elminator Only W/PN RE1801/RE1807 – RE1898-155
TJ CVF Rear Drive Shaft. Spicer drive shafts and components are as good as they get. This drive shaft is compatible with the RE1807, RE1801 Slip yoke eliminator kits and Currie Enterprises tail shaft conversion kits. Measurements are taken from flange face to center of the rear u-joint with the slip stub at the center of its travel. measure your vehicle on the ground in the running position to get correct length.
Details:- 15.5 inch long
- For use with part number RE1801 and RE1807
- Will only work on flange style slip yoke eliminator
SKU: RE1898-155 -
Drive Shaft
Rubicon Express CVO Drive Shaft Rear 19.5 Inch 1310 Series Yoke W/PN RE1811 – RE1860-195
CVO Rear Driveshaft. Rubicon Express drive shafts and components are as good as they get. Atlas transfer cases and any other 1310 series CV yoke. Measurements are taken center to center on the u-joint with the slip stub at the center of its travel. Measure your vehicle on the ground in the running position to get correct length.
Details:- 19.5 Inches Long
- 1310 Series Yoke
SKU: RE1860-195 -
Drive Shaft
Rubicon Express CVO Drive Shaft Rear 18.5 Inch 1310 Series Yoke W/PN RE1811 – RE1860-185
CVO Rear Driveshaft. Rubicon Express drive shafts and components are as good as they get. Atlas transfer cases and any other 1310 series CV yoke. Measurements are taken center to center on the u-joint with the slip stub at the center of its travel. Measure your vehicle on the ground in the running position to get correct length.
Details:- 18.5 Inches Long
- 1310 Series Yoke
SKU: RE1860-185 -
Drive Shaft
Jeep TJ Rear CV-Style Drive Shaft 97-06 Wrangler TJ Pro Comp Suspension
Pro Comp’s rear CV replacement driveshafts are designed to be used with Pro Comp slip yoke eliminator kits. They’re 2-piece style driveshafts made of high-quality steel.
Details:- Fits 1997 to 2006 TJ Wrangler
- 4-5 Inch of lift
- For use with slip yoke eliminator
- CV style drive shaft
- 21.5 Inch extended
SKU: 4042-PRO
