Category: Winch Fairlead
Tags: Winch & Recovery, Winch Accessories, Winch Fairlead
Brand: Smittybilt
Winch Fairlead
Aluminum Hawse Fairlead Polished W/ No Logo Smittybilt – 2809
The Cloak Extended Mesh Top gives you the best of both worlds; reduces the heat and glare of the sun while allowing the cool air to flow through the unique mesh design. Manufactured out of durable long lasting PVC coated mesh material, UV treated material. Easy and quick install no other hardware required.
Details:
- Fits 2007 to 2018 JK Wrangler Unlimited and Rubicon Unlimited
- 4-door models
- Black mesh
- Extended Mesh Top only
- Easy install no tools needed
- No header required
- Stays on with hard or soft top installed
- Reduces wind noise
- Installs with heavy-duty bungee cords
- UV and mildew resistant
- Durable long lasting PVC coated mesh material
- Reduces the heat and glare of the sun while allowing cool air to flow through
- Rear and sides sold separately part S/B95501
$36.99
Related products
-
Winch Fairlead
Hawse Fairlead 1 Inch Thick Gun Metal Gray Factor 55
Factor 55 introduces a new line of Aluminum Hawse Fairleads. The 1.0 fairleads are CNC machined from 1 inch thick USA 6000 series aluminum bar. The industry standard fairlead thickness is .75 inches thick.
The thicker aluminum bar results in a larger outer fillet radius for the synthetic rope to slide against. This results in less stress on the rope fibers during high angular pulls, increasing the life of your synthetic rope.The 1.0 and 1.5 fairleads are the industry’s first Hawse fairleads compatible with larger 1/2 inch diameter rope tube thimbles.
The rope slot height opening is taller to allow the larger 1/2 inch tube thimbles to pass through. There is also a machined outer corner chamfer to reduce rope stress for those than plan on using the winch as a front suspension suck down device. These fairleads come in a durable MIL-A-8625F TYPE III gun metal gray hard anodized finish with a laser engraved logo.
What is the best surface finish for Hawse aluminum fairleads? Without a doubt it is a Type III hard anodized coating. Not cosmetic Type II anodized finishes, not powder coated, and not raw or polished aluminum. Why? Because a hard coating can resist the abrasion damage from a dirty/gritty synthetic winch rope rubbing across it. Especially during extreme side pulls where rope fiber stresses are extremely high. A Mil-A-8625 Type III hard anodized finish leaves a .002 inch thick Al2O3 ceramic coating that is in the top 5 hardest materials known to mankind. Not too far away from diamond hardness actually.
Another valuable material property from hard anodized coatings are the low coefficients of friction. Low friction = lower rope heat. Only drawback? Hard anodizing is not offered in typical bright and fancy anodized colors. All Factor 55 fairleads only come in Mil-A-8625 hard gray finishes. Not fancy, but it is the proper finish to extend the life of your synthetic rope.
Features:- Size: 1 inch
- Overall Dimension: 12.35 x 3.25 inch
- Material: 6160 Aluminum
- Finish: Gun Metal Gray
- Made in the USA
- For synthetic winch rope only
- Fairleads Do not come with mounting hardware.
The reason for this is depending on your vehicle, bumper, and fairlead mounting thicknesses the shank length of the bolts may need to be longer or shorter to prevent the bolts from contacting the body of your winch. In most cases the mounting bolts that are supplied by your winch manufacturer are adequate in strength and length. In some cases longer bolts are required and 3/8 inch Grade 5-Grade 8 bolts in 1.25-1.5 inch shank length is a good starting point for fitment. 7/16 inch bolts may also be used. Please contact us for any specific questions.
SKU: 00016--GGBW -
D Ring Shackle
D-Ring 1/2 Inch 2 Ton Rating Black Smittybilt – 13046B
Smittybilts fender flares are produced for you in a textured UV stable ABS plastic. This ABS plastic is strong enough for the trail and looks good enough for the city streets. Its durable construction allows it to be flexible without cracking. Bolt it on or paint it first to match your Jeeps paint job. Minimal drilling may be needed for proper installation.
Details:- Fits 1987 to 1995 YJ Wrangler
- Black textured UV stable ABS Plastic
- 4 piece set
- Provides 6 Inch of coverage
- Requires drilling
SKU: n/a -
Winch Fairlead
Aluminum Hawse Fairlead Comp Series Polished W/ XRC Logo Smittybilt – 2805
Smittybilt is proud to introduce their new Cloak Extended Mesh Top, which allows you to enjoy the open air from the shade of your Jeeps passenger compartment. Available for 97-06 Jeep Wrangler TJs and both two door and four door 07-18 Jeep Wrangler JKs, the Cloak is made from durable PVC-coated mesh that is resistant to both ultraviolet rays and mildew. The Smittybilt Cloak installs easily using heavy duty bungee cords with no tools required and fits under standard hard tops or soft tops. Double layer stitching allow the Cloak to shrug off even the largest gusts of wind.
Details:- Black mesh
- Rear and sides only
- Reduces wind noise
- Installs with heavy duty bungee cords
- UV and mildew resistant
- Durable long lasting PVC coat mesh material
- Reduces the heat and glare of the sun while allowing cool air to flow through
- For use with Smittybilt Extended Mesh Top part S/B95500
SKU: n/a -
D Ring Shackle
D-Ring 7/8 Locking Pin 6.5 Tons (Black)Smittybilt – 13050B
Designed for early-model CJ vehicles. Rugged contoured seat with firm comfortable spring suspension. Installation is quick and easy using the same mounting hardware and bolts from the original seats.
Details:- Fits 1955 to 1976 CJ
- Traditional black vinyl
- Rugged contoured seat with firm comfortable spring suspension
- Uses same mounting hardware and bolts from original seats
- Passenger side seat bracket will need modified on 1955-75 CJ Foots
SKU: n/a -
Winch Fairlead
Hawse Fairlead 1.5 Inch Thick Gun Metal Gray Factor 55
Factor 55 introduces a new line of Aluminum Hawse Fairleads. The 1.5 fairleads are CNC machined 1.5 inch thick USA 6000 series aluminum bar. The industry standard fairlead thickness is .75 inches thick.
The thicker aluminum bar results in a larger outer fillet radius for the synthetic rope to slide against. This results in less stress on the rope fibers during high angular pulls, increasing the life of your synthetic rope.The 1.0 and 1.5 fairleads are the industry’s first Hawse fairleads compatible with larger 1/2 inch diameter rope tube thimbles.
The rope slot height opening is taller to allow the larger 1/2 inch tube thimbles to pass through. There is also a machined outer corner chamfer to reduce rope stress for those than plan on using the winch as a front suspension suck down device. These fairleads come in a durable MIL-A-8625F TYPE III gun metal gray hard anodized finish with a laser engraved logo.
What is the best surface finish for Hawse aluminum fairleads? Without a doubt it is a Type III hard anodized coating. Not cosmetic Type II anodized finishes, not powder coated, and not raw or polished aluminum. Why? Because a hard coating can resist the abrasion damage from a dirty/gritty synthetic winch rope rubbing across it. Especially during extreme side pulls where rope fiber stresses are extremely high. A Mil-A-8625 Type III hard anodized finish leaves a .002 inch thick Al2O3 ceramic coating that is in the top 5 hardest materials known to mankind. Not too far away from diamond hardness actually.
Another valuable material property from hard anodized coatings are the low coefficients of friction. Low friction = lower rope heat. Only drawback? Hard anodizing is not offered in typical bright and fancy anodized colors. All Factor 55 fairleads only come in Mil-A-8625 hard gray finishes. Not fancy, but it is the proper finish to extend the life of your synthetic rope.
Features:- Size: 1.5 inch
- Overall Dimension: 12.35 x 3.25 inch
- Material: 6160 Aluminum
- Finish: Gun Metal Gray
- Made in the USA
- For synthetic winch rope only
- Fairleads Do not come with mounting hardware.
The reason for this is depending on your vehicle, bumper, and fairlead mounting thicknesses the shank length of the bolts may need to be longer or shorter to prevent the bolts from contacting the body of your winch. In most cases the mounting bolts that are supplied by your winch manufacturer are adequate in strength and length. In some cases longer bolts are required and 3/8 inch Grade 5-Grade 8 bolts in 1.25-1.5 inch shank length is a good starting point for fitment. 7/16 inch bolts may also be used. Please contact us for any specific questions.
SKU: 00019--GGBW
