Winch Fairlead
Showing all 13 results
-
Winch Fairlead
Aluminum Hawse Fairlead Comp Series Polished W/ XRC Logo Smittybilt – 2805
Smittybilt is proud to introduce their new Cloak Extended Mesh Top, which allows you to enjoy the open air from the shade of your Jeeps passenger compartment. Available for 97-06 Jeep Wrangler TJs and both two door and four door 07-18 Jeep Wrangler JKs, the Cloak is made from durable PVC-coated mesh that is resistant to both ultraviolet rays and mildew. The Smittybilt Cloak installs easily using heavy duty bungee cords with no tools required and fits under standard hard tops or soft tops. Double layer stitching allow the Cloak to shrug off even the largest gusts of wind.
Details:- Black mesh
- Rear and sides only
- Reduces wind noise
- Installs with heavy duty bungee cords
- UV and mildew resistant
- Durable long lasting PVC coat mesh material
- Reduces the heat and glare of the sun while allowing cool air to flow through
- For use with Smittybilt Extended Mesh Top part S/B95500
SKU: n/a -
Winch Fairlead
Aluminum Hawse Fairlead Polished W/ No Logo Smittybilt – 2809
The Cloak Extended Mesh Top gives you the best of both worlds; reduces the heat and glare of the sun while allowing the cool air to flow through the unique mesh design. Manufactured out of durable long lasting PVC coated mesh material, UV treated material. Easy and quick install no other hardware required.
Details:- Fits 2007 to 2018 JK Wrangler Unlimited and Rubicon Unlimited
- 4-door models
- Black mesh
- Extended Mesh Top only
- Easy install no tools needed
- No header required
- Stays on with hard or soft top installed
- Reduces wind noise
- Installs with heavy-duty bungee cords
- UV and mildew resistant
- Durable long lasting PVC coated mesh material
- Reduces the heat and glare of the sun while allowing cool air to flow through
- Rear and sides sold separately part S/B95501
SKU: n/a -
Winch Fairlead
Aluminum Hawse Winch Fairlead Poison Spyder – 45-45-010
The Poison Spyder Aluminum Hawse Fairlead will help protect your synthetic winchline during winch operation, as well as give the front of your 4X4 a little bit of Poison Spyder attitude.
CNC machined from billet aluminum and powdercoated for a durable finish.
Features:- CNC machined from 6061-T6 billet aluminum
- Provides a smooth surface to feed synthetic winch rope through without snags or wear
- Semi-gloss black powdercoat finish
- Poison Spyder logo CNC machined through the powdercoat
- Stainless steel hardware and install instructions included
SKU: 45-45-010-PSC -
Winch Fairlead
Hawse Fairlead 1 Inch Thick Gun Metal Gray Factor 55
Factor 55 introduces a new line of Aluminum Hawse Fairleads. The 1.0 fairleads are CNC machined from 1 inch thick USA 6000 series aluminum bar. The industry standard fairlead thickness is .75 inches thick.
The thicker aluminum bar results in a larger outer fillet radius for the synthetic rope to slide against. This results in less stress on the rope fibers during high angular pulls, increasing the life of your synthetic rope.The 1.0 and 1.5 fairleads are the industry’s first Hawse fairleads compatible with larger 1/2 inch diameter rope tube thimbles.
The rope slot height opening is taller to allow the larger 1/2 inch tube thimbles to pass through. There is also a machined outer corner chamfer to reduce rope stress for those than plan on using the winch as a front suspension suck down device. These fairleads come in a durable MIL-A-8625F TYPE III gun metal gray hard anodized finish with a laser engraved logo.
What is the best surface finish for Hawse aluminum fairleads? Without a doubt it is a Type III hard anodized coating. Not cosmetic Type II anodized finishes, not powder coated, and not raw or polished aluminum. Why? Because a hard coating can resist the abrasion damage from a dirty/gritty synthetic winch rope rubbing across it. Especially during extreme side pulls where rope fiber stresses are extremely high. A Mil-A-8625 Type III hard anodized finish leaves a .002 inch thick Al2O3 ceramic coating that is in the top 5 hardest materials known to mankind. Not too far away from diamond hardness actually.
Another valuable material property from hard anodized coatings are the low coefficients of friction. Low friction = lower rope heat. Only drawback? Hard anodizing is not offered in typical bright and fancy anodized colors. All Factor 55 fairleads only come in Mil-A-8625 hard gray finishes. Not fancy, but it is the proper finish to extend the life of your synthetic rope.
Features:- Size: 1 inch
- Overall Dimension: 12.35 x 3.25 inch
- Material: 6160 Aluminum
- Finish: Gun Metal Gray
- Made in the USA
- For synthetic winch rope only
- Fairleads Do not come with mounting hardware.
The reason for this is depending on your vehicle, bumper, and fairlead mounting thicknesses the shank length of the bolts may need to be longer or shorter to prevent the bolts from contacting the body of your winch. In most cases the mounting bolts that are supplied by your winch manufacturer are adequate in strength and length. In some cases longer bolts are required and 3/8 inch Grade 5-Grade 8 bolts in 1.25-1.5 inch shank length is a good starting point for fitment. 7/16 inch bolts may also be used. Please contact us for any specific questions.
SKU: 00016--GGBW -
Winch Fairlead
Hawse Fairlead 1.5 Inch Thick Gun Metal Gray Factor 55
Factor 55 introduces a new line of Aluminum Hawse Fairleads. The 1.5 fairleads are CNC machined 1.5 inch thick USA 6000 series aluminum bar. The industry standard fairlead thickness is .75 inches thick.
The thicker aluminum bar results in a larger outer fillet radius for the synthetic rope to slide against. This results in less stress on the rope fibers during high angular pulls, increasing the life of your synthetic rope.The 1.0 and 1.5 fairleads are the industry’s first Hawse fairleads compatible with larger 1/2 inch diameter rope tube thimbles.
The rope slot height opening is taller to allow the larger 1/2 inch tube thimbles to pass through. There is also a machined outer corner chamfer to reduce rope stress for those than plan on using the winch as a front suspension suck down device. These fairleads come in a durable MIL-A-8625F TYPE III gun metal gray hard anodized finish with a laser engraved logo.
What is the best surface finish for Hawse aluminum fairleads? Without a doubt it is a Type III hard anodized coating. Not cosmetic Type II anodized finishes, not powder coated, and not raw or polished aluminum. Why? Because a hard coating can resist the abrasion damage from a dirty/gritty synthetic winch rope rubbing across it. Especially during extreme side pulls where rope fiber stresses are extremely high. A Mil-A-8625 Type III hard anodized finish leaves a .002 inch thick Al2O3 ceramic coating that is in the top 5 hardest materials known to mankind. Not too far away from diamond hardness actually.
Another valuable material property from hard anodized coatings are the low coefficients of friction. Low friction = lower rope heat. Only drawback? Hard anodizing is not offered in typical bright and fancy anodized colors. All Factor 55 fairleads only come in Mil-A-8625 hard gray finishes. Not fancy, but it is the proper finish to extend the life of your synthetic rope.
Features:- Size: 1.5 inch
- Overall Dimension: 12.35 x 3.25 inch
- Material: 6160 Aluminum
- Finish: Gun Metal Gray
- Made in the USA
- For synthetic winch rope only
- Fairleads Do not come with mounting hardware.
The reason for this is depending on your vehicle, bumper, and fairlead mounting thicknesses the shank length of the bolts may need to be longer or shorter to prevent the bolts from contacting the body of your winch. In most cases the mounting bolts that are supplied by your winch manufacturer are adequate in strength and length. In some cases longer bolts are required and 3/8 inch Grade 5-Grade 8 bolts in 1.25-1.5 inch shank length is a good starting point for fitment. 7/16 inch bolts may also be used. Please contact us for any specific questions.
SKU: 00019--GGBW -
Winch Fairlead
Hawse Offset Fairlead 1.5 Inch Thick Factor 55
Factor 55 introduces a new Aluminum Hawse Offset Fairlead. These 1.5 inch fairleads are CNC machined from 1.5 inch thick USA 6000 series aluminum bar. The industry standard fairlead thickness is .75 inches thick.
The thicker aluminum bar results in a larger outer fillet radius for the synthetic rope to slide against. This results in less stress on the rope fibers during high angular pulls, increasing the life of your synthetic rope. The Offset fairleads are the industry’s first Hawse Offset fairlead compatible with larger 1/2 inch diameter rope tube thimbles.The rope slot height opening is taller to allow the larger 1/2 inch tube thimbles to pass through. There is also a machined outer corner chamfer to reduce rope stress for those than plan on using the winch as a front suspension suck down device. These fairleads come in a durable MIL-A-8625F TYPE III gun metal gray hard anodized finish with a laser engraved logo.
What is the best surface finish for Hawse aluminum fairleads? Without a doubt it is a Type III hard anodized coating. Not cosmetic Type II anodized finishes, not powder coated, and not raw or polished aluminum.Why? Because a hard coating can resist the abrasion damage from a dirty/gritty synthetic winch rope rubbing across it. Especially during extreme side pulls where rope fiber stresses are extremely high. A Mil-A-8625 Type III hard anodized finish leaves a .002 inch thick Al2O3 ceramic coating that is in the top 5 hardest materials known to mankind (See chart under Corundum/Sapphire). Not too far away from diamond hardness actually. Another valuable material property from hard anodized coatings are the low coefficients of friction. Low friction = lower rope heat.
Only drawback? Hard anodizing is not offered in typical bright and fancy anodized colors. All Factor 55 fairleads only come in Mil-A-8625 hard gray finishes. Not fancy, but it is the proper finish to extend the life of your synthetic rope.
Features:
Size:1.5 inch
Overall Dimension: 11.75 x 3.25 inch
Offset Opening: .80 inch
Thickness: 1.5 inch
For synthetic winch rope only.SKU: 00026--GGBW -
Winch Fairlead
Recovery Strap Shorty Strap II 3 Foot 2 Inch Factor 55
At Factor 55 we have been using a version of our custom ultra short flat straps for years to assist in a variety of useful vehicle recovery applications. These short straps are not constructed like typical recovery/snatch straps. The Shorty Straps are not designed to store energy from stretch. They are designed to serve as a versatile short soft link to attach to vehicles and are constructed of an ultra low stretch (low energy storage) polyester, not high stretch nylon like typical snatch straps.
The applications vary from easily attaching to vehicles that are not equipped with recovery points, to using your winch and Shorty Strap to field repair/straighten bent steering components like tie rods and drag links. The inherit flat shape of the straps prevent the straps from rolling and twisting when attached to tubular shapes like bumper stingers, steering components, and nerf bars. We prefer flat straps over round ropes for this reason.
Even polyester webbing materials retain a small element of material stretch and since the total energy stored is a function of the percent of stretch and the overall length of the strap, we have designed the strap to be as short as possible but still retain the necessary webbing overlap and stitch count necessary for the rated loads.
The overall length of the Shorty Straps is 3 feet, and this is reduced to only 1.5 feet long when used in the common basket configuration. Low stretch/energy storage equates to less recoil energy during a possible component failure.
Features:- Length: 3 Foot
- Width: 2 inch
- Material: Polyester Webbing
- Design Type: Flat
These straps are manufactured in the USA to Factor 55 specifications by the Certified Sling Corporation, the parent company to the well known Bubba Rope Company.
SKU: 00078--GGBW -
Winch Fairlead
Recovery Strap Shorty Strap III 3 Foot 3 Inch Factor 55
At Factor 55 we have been using a version of our custom ultra short flat straps for years to assist in a variety of useful vehicle recovery applications. These short straps are not constructed like typical recovery/snatch straps. The Shorty Straps are not designed to store energy from stretch. They are designed to serve as a versatile short soft link to attach to vehicles and are constructed of an ultra low stretch (low energy storage) polyester, not high stretch nylon like typical snatch straps.
The applications vary from easily attaching to vehicles that are not equipped with recovery points, to using your winch and Shorty Strap to field repair/straighten bent steering components like tie rods and drag links. The inherit flat shape of the straps prevent the straps from rolling and twisting when attached to tubular shapes like bumper stingers, steering components, and nerf bars. We prefer flat straps over round ropes for this reason.
Even polyester webbing materials retain a small element of material stretch and since the total energy stored is a function of the percent of stretch and the overall length of the strap, we have designed the strap to be as short as possible but still retain the necessary webbing overlap and stitch count necessary for the rated loads.
The overall length of the Shorty Straps is 3 feet, and this is reduced to only 1.5 feet long when used in the common basket configuration. Low stretch/energy storage equates to less recoil energy during a possible component failure.
Features:- Length: 3 Foot
- Width: 3 inch
- Material: Polyester Webbing
- Design Type: Flat
These straps are manufactured in the USA to Factor 55 specifications by the Certified Sling Corporation, the parent company to the well known Bubba Rope Company.
SKU: 00079--GGBW -
Winch Fairlead
Roller Fairlead 4 Way Smittybilt – 97281-47
This roller fairlead guides your wire rope onto the drum and protects it by reducing friction and excessive wear on winch cables or wire ropes, especially during high angle pulls. It is easy to install and works with all standard winch plates.
Details:- Mounts directly to all standard winch mounting plates
- Reduces excessive wear on your winch cable or wire rope
SKU: n/a -
Winch Fairlead
Roller Fairlead Low Profile 4 Way Smittybilt – 2810
This roller fairlead guides your wire rope onto the drum and protects it by reducing friction and excessive wear on winch cables or wire ropes, especially during high angle pulls. It is easy to install and works with all standard winch plates.
Details:- Low Profile
- 4 rollers
- Fits standard winch plates
- All mounting hardware included
SKU: n/a -
Winch Fairlead
Rubicon Express Billet Winch Fairlead Aluminum – RE1025
Billet Fairlead to keep your Synthetic Winch Rope safe with this stylish Rubicon Express Billet Fairlead.
Details:- Universal design
- Constructed of billet aluminum
- Low-profile and lightweight
- Stealth black anodized finish
SKU: RE1025 -
Winch Fairlead
Winch Fairlead Mount Poison Spyder – 45-57-010
The Poison Spyder Winch Fairlead Mount installs between the winch and the bumper to provide a mounting surface for the winch fairlead. The Winch Fairlead Mount is designed to fit the 10 inch x 4.5 inch bolt pattern common to Most Warn winches except 8274. Many other winch brands use the same bolt pattern.
The Winch Fairlead Mount is designed to fit the winch rope slot and 10 inch bolt pattern of Most Warn or common aftermarket roller or Hawse fairleads, including the Poison Spyder Aluminum Hawse Winch Fairlead (P/N 45-45-010).
Features:- CNC laser cut, precision brake-formed 3/16 inch plate steel
- Provides easy, convenient mounting solution for both roller and hawse style winch fairleads
- Matches common winch and winch fairlead bolt patterns
- Semi-gloss black powdercoat finish
SKU: 45-57-010-PSC -
Winch Fairlead
Zeon Winch Spacer Plates Poison Spyder – 45-57-010-03
Zeon Winch Spacer Plates. Use these Spacer Plates when mounting a Warn Zeon Winch on to your Poison Spyder Brawler Lite, Brawler Mid, or JK RockBrawler front bumper. On these bumpers, the slight recess along the top surface of the bumper is just slightly incompatible with the extra wide, low housing ends on the Zeon winches.
Simply lifting the winch about an extra 1/8 inch solves this problem. These spacers are a convenient way to do that, by simply placing them between the winch and the fairlead mount to provide the lift needed. CNC laser cut from 3/16 inch plate steel, powdercoated black.
Features:- CNC laser cut 3/16 plate steel
- Provides extra height needed to mount Zeon winches with certain bumpers
- Semi-gloss black powdercoat finish
- Important: Brawler Mid Front Bumpers will require Two pairs of spacer plates to install the Warn Zeon winch.
SKU: 45-57-010-03-PSC
